How does the EGR effect engine performance?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 4, 2004
Threads
100
Messages
2,574
Location
Tucson AZ
I finally was able to address my 'code 71' this weekend with tarbe and Buckru. I replaced the EGR modulator, valve and all vacuum lines leading to and fro. In addition I cleaned up the temp sensor which looked pretty nasty.

The good news is no more CEL after ~80 miles and knock-on-wood, there will be no more.

My question is how does the EGR system effect engine performance? I don't know if it is in my head, but the idle seems more smooth and is now around 600 rmp instead of 650 as it used to be. It also feels a bit more peppy, but this could just be another mind trick thing.

Then again, this could just be due to the new steering stabilizer I put on too.

Thanks,

Ross
 
Baggins is right. Your hg is blowing as we speak.

Buck
The John Schotts Lifetime Achievement Award Reipient
( notice I use recipient and not winner for specific reasons)
 
If you have the check engine light on due to "Insufficient EGR Flow"

it will increase emissions by 1.5%, so you can't pass the DEQ req.s

---Has anyone had the check engine light go on and scaned it and

had it read "Insufficient EGR flow"? wondering what to do here

exactly...

I have read that to prevent this problem replacing this Blue cap

below with the Green one that came out in later TLCs is a good idea.

Apparently Toyota realized that this was a problem and changed it..



EventsJuly2006.jpg
 
Sackman said:
---Has anyone had the check engine light go on and scaned it and

had it read "Insufficient EGR flow"?
That's the code I threw right after getting it smogged. Haven't done anything about it yet. I was going to just go ahead and replace the VSV and Modulator.
 
It that a pretty cheap fix? an do you think that it will take care

of the "insuficient EGR flow"?

...Im guessing you wouldnt know about changing to a green cap.

better.. worse?
 
Sackman said:
It that a pretty cheap fix? an do you think that it will take care

of the "insuficient EGR flow"?

...Im guessing you wouldnt know about changing to a green cap.

better.. worse?
I still have the original blue. From what I understand, changing the EGR VSV & Modulator out may fix the problem.
 
Sackman said:
If you have the check engine light on due to "Insufficient EGR Flow"

it will increase emissions by 1.5%, so you can't pass the DEQ req.s

---Has anyone had the check engine light go on and scaned it and

had it read "Insufficient EGR flow"? wondering what to do here

exactly...

I have read that to prevent this problem replacing this Blue cap

below with the Green one that came out in later TLCs is a good idea.

Apparently Toyota realized that this was a problem and changed it..

I was thinking it was just the opposite - - changing it for a previous/older part number
 
GeoRoss said:
I finally was able to address my 'code 71' this weekend with tarbe and Buckru. I replaced the EGR modulator, valve and all vacuum lines leading to and fro. In addition I cleaned up the temp sensor which looked pretty nasty.

The good news is no more CEL after ~80 miles and knock-on-wood, there will be no more.

My question is how does the EGR system effect engine performance? I don't know if it is in my head, but the idle seems more smooth and is now around 600 rmp instead of 650 as it used to be. It also feels a bit more peppy, but this could just be another mind trick thing.

Then again, this could just be due to the new steering stabilizer I put on too.

Thanks,

Ross

Ross - tell us about the job replacing that stuff - 1 banana?
Mind sharing what all that set you back?
 
Sackman said:
---Has anyone had the check engine light go on and scaned it and had it read "Insufficient EGR flow"? wondering what to do here exactly...

There have been about 200 of us with "EGR Flow Insufficient" aka P0401. Most have fixed the problem and there is no single fix and there is no "easy" fix. Don't be misled by the "green" vs "blue" modulator. If yours is good the test will pass. If it is bad, it won't.

The way to fix this problem is to isolate the failing component; the EGR modulator, the EGR valve, the VSV for EGR, the EGR temp sensor, or the interconnecting hoses. Some have found multiple failures; presumably because one part that fails will lead to "clogging" of another part. For example, some feel that a failed VSV for EGR will increase the carbon and lead to a failing EGR modulator (or vice versa.)

There are specific tests in the FSM. Follow the charts and test each component. The VSV for EGR is the hardest to test because it's located under the intake and has to be removed in order to test it. Most people won't test it but that piece is also one of the most common failures. It gets clogged up with carbon or something.

-B-
 
I believe the green is the old version and the blue is the new version. My '97 has a green cap and is in need of replacement.;p

Replacing the modulator is not even a 1/2 bannana job if you have opposible thumbs. The VSV is a bit more difficult since it's under the intake.
 
Scamper said:
I believe the green is the old version and the blue is the new version.

IIRC, 80's came with the green (at least in later models), and Toyota's replacement for it is the blue, so you could call it the 'new' version. However, I believe the blue one is the same one used in FJ6x's and possibly early 80's, so it might also be referred to as the 'old' one. Have fun with that.

-Spike
 
Sackman, for those of us with pre-ODBII, all you know is that there is a EGR/VSV problem, code 71. There is no insight as to what it could be. In order to be thorough, you have to check each component individually.

MoJ, as to how I approached it, I needed a place to do it first as I am in temporary shelter that doesn't allow wrenching. I also wanted a little back-up person behind me as well. Thanks tarbe, he provided both.

I decided to tackle the problem by throwing parts at the EGR system. I would have liked to have tested individual components first and just get the ones I needed, but I didn't have the time to do so. I also wimped out on pulling the VSV to check its functioning other than to look at the hoses and what not.

1. The EGR modulator. It was green and now blue. The green one upon dissection didn't look very cruded up. I performed a variation of the FSM check and found that the port (not the P or R) that goes to the EGR valve seemed clogged. After blowing awhile, free air could move.

2. EGR valve. I didn't have acces to a vacuum and wasn't about to suck on that nasty looking thing. The hardest thing about this was getting the pipe nut loose enough to undo it (and the reverse). Getting the studs out with torx (sp?) socket made life easy. The FSM says do it with pliers though. The thing was nasty and I was glad to change it out.

3. temp sensor. This thing was nasty. I polished it with steel wool gently until I had removed all the carbon deposits.

4. The bottom tube that is bigger than the other vacuum lines. I wish I had gotten a replacement for it. I would have if I had know it was not the same size as the vacuum lines. In any event I cleaned it out very well. An amazing amount of carbon came out.

5. All other vacuum lines. I replaced all lines leading into and out of the EGR system as well as tried to ream out any ports. Much easier than cleaning the old tubing.

6. Fingers crossed after ~150 miles of mixed driving.

I am still curious if I am all goofy on the more pep and smoother idle. Either way I am happy.

Ross
 
I cleaned all my tubes, pipes, and connections, replaced the green with the blue, and at exactly 200 miles on the freeway, the CEL came back on. I did not change the VSV or check the temp sensor yet though. Those are next. It did seem better for the first 200 miles. I know it took off faster in town. Possibly more of a computer response than a mechanical response though.
 
Lucy said:
I did not change the VSV or check the temp sensor yet though. Those are next.

We have had reports of many bad VSVs. AFAIK, there has only been 1 reported bad EGR temp sensor. Clean it, test it and don't replace it unless it fails the test. Those temp sensors are easy to remove but they are spendy.

-B-
 
We have had reports of many bad VSVs. AFAIK, there has only been 1 reported bad EGR temp sensor. Clean it, test it and don't replace it unless it fails the test. Those temp sensors are easy to remove but they are spendy.

-B-

I'd like to clean mine as I'm sure it needs it ...... however, I am having a :mad: #$%& of a time getting it loose. Am I missing something here? Using an open end 14mm wrench, it's starting to round the corners, already hit it with PB blaster the last 2 days. Any "tricks" I should know about? Should I be trying when things are warm or cold? I'm being a bit easy on it as it's in the aluminum and I don't want to bung it up. What am I missing?
 
I'd like to clean mine as I'm sure it needs it ...... however, I am having a :mad: #$%& of a time getting it loose. Am I missing something here? Using an open end 14mm wrench, it's starting to round the corners, already hit it with PB blaster the last 2 days. Any "tricks" I should know about? Should I be trying when things are warm or cold? I'm being a bit easy on it as it's in the aluminum and I don't want to bung it up. What am I missing?

Cleaning mine completely resolved my CEL. I have a 94 so it's located in a different spot - harder to get to - but the nut is the same. It was tough to get cracked loose. I know what you mean about the corners rounding easily. I ended up putting a open end wrench on it and then tapping the end of the wrench with a hammer. It popped loose with a few taps.
 
Back
Top Bottom