How does the EGR effect engine performance?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I had the P0401 code come up when the light came on. Did the VSV(blue to green) and did the front O2 sensor and cleaned the temp sensor. It came on a few times and then it would go off after a few days. Finally got the chane to check the code and got the parts to fix the issue. Did it last Monday and the f&%#*g light came on again today. Gonna check it tomorrow. I'll post my results tomorrow.


Montana Cruiser: try a brake line wrench. Kinda like a box end wrench but one end is cut out to fit around a brake line.
:beer:
 
That would be the EGR modulator. The VSV for EGR is located underneath the intake.



Mine came out easily. Try a 6pt boxed end or a line wrench.

-B-

-B-

I think I am going to look into the line wrench, maybe I can find an inexspensive set seeing as I will need them to upgrade the brake lines at some point as well. Maybe the local Sears?

Nate
 
To the title of this thread, EGR is not active during idle nor wide open throttle, so has little effect engine performance when working as it is supose to.

If your EGR had failed in such a way that it was leaking exhaust gas during idle then it would idel poorly, as far as I can see that EGR valve itself is the only failed part that could cause that.

So if it was the EGR vavle (that you replaced?) that was bad then it is a posibility that you are idling better.


My P0401 adventure I had a still working but leaking modulator, a VSV that passed the FSM test but was intermittently failing in the truck.

some troubleshooting info here:

https://forum.ih8mud.com/showpost.php?p=1535318&postcount=10
 
To the title of this thread, EGR is not active during idle nor wide open throttle, so has little effect engine performance when working as it is supose to.

If your EGR had failed in such a way that it was leaking exhaust gas during idle then it would idel poorly, as far as I can see that EGR valve itself is the only failed part that could cause that.

So if it was the EGR vavle (that you replaced?) that was bad then it is a posibility that you are idling better.


My P0401 adventure I had a still working but leaking modulator, a VSV that passed the FSM test but was intermittently failing in the truck.

some troubleshooting info here:

https://forum.ih8mud.com/showpost.php?p=1535318&postcount=10

Thanks, I am now about 3k miles and 5 months post fix with no CEL. So what ever I did seems to have cured it, until the VSV fails that is. :)

Someone had mentioned to me that with the EGR acting goofy, the ECM would retard the timing (?). In any event, I am running smoother and with more pep. It may all be in my head, but I am good with that too.

Ross
 
Ran the code at the shop, still have insufficient EGR flow, gonna go ahead and get the VSV today and hopefully the light will stay off. Pisses me off when that damn light comes on. Let ya'll know again.
:beer:
 
Ross, I noticed that nobody answer you original question; maybe I can help.
The EGR serves an important function, it helps lower combustion temperatures.
By lowering combustion temperatures it allows the computer to give the engine more
timming advance (Better Performance) under light, moderate acceleration and cruising
speeds, it also reduces NOx emissions.
As far is I know EGRs are not operational at idle, therefor the idle speed difference you
described may not be related to the EGR, unless the EGR system had a leak.
I hope this answers your question...


Ruben
 
Last edited:
That would be the EGR modulator. The VSV for EGR is located underneath the intake.



Mine came out easily. Try a 6pt boxed end or a line wrench.

-B-

Bummer, bought a line wrench today and no go, the relief in end that I assume would cup a flare offset the teeth enough it would not grab the nut, too tight against the intake.
 
Back
Top Bottom