Help! Broken Cruiser. Engine issues

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

ok.. well in the course of taping the videos, it finally went above 2100RPMs, but it stumbles at that point, then either falls or revs up... the first video shows what it was doing, the second one shows its new state of not working...

YouTube - FZJ80 Landcruiser 2300rpm Engine Cut-out
YouTube - FZJ80 Land Cruiser Engine Cut-out

Now I'm leaning towards a bad TPS due to weird throttle response, but I'm still not getting a CEL... and its improving... maybe it got water in it?
 
Just went out and tried it again... its getting better, and the idle is starting to return to normal after it screws up... maybe it just needs to be driven... i'm betting it got water in something, and i'm thinking the TPS....
 
Could be spark plug wires. If they are original, replace them for sure (they need it anyway). If they are OEM, they will have the year of mfg on them. They may appear to be good, and all send a spark when tested, but I have seen them be the culprit many times. Go OEM with the plug wires. Cdan can have 'em to you in a couple days.
 
plugs and wires are in the near future.....

corvette and dodge need an oil change first... 20 quarts of synthetic, two oil filters, and a fuel filter doesnt appear to be cheap. after that, cruiser will get the goods.
 
plugs and wires are in the near future.....

corvette and dodge need an oil change first... 20 quarts of synthetic, two oil filters, and a fuel filter doesnt appear to be cheap. after that, cruiser will get the goods.

FYI, I just saw (at walmart, maybe?) Delo synthetic for the first time. It was relatively cheap, less than $20 for a gallon jug, IIRC.
 
thanks!

unfortunately, the vette only gets mobil 1 0-20 and the dodge will probably get either rotella or mobil one 5-40 syn.

Rotella Syn is about the same price as the delo synthetic at walmart. Why wouldn't you go with the delo synthetic, heard anything about it? I know the Delo (regular/dino) has a good rep for diesels, I would assume that the Delo synth would be even better...
 
delo has a great rep... so does rotella.

I didnt realize they made a syn... actually when I read your post i assumed it was dino... 20 isnt bad at all... rotella runs me about 21 a gal. do you remember what weight the delo syn was? I'll have to go to wally world and check it out.
 
My fj 80 did that exact thing after i washed it out, I replaced the plugs and wires and it was perfect. They were orig. and water got in all sorts of places on the wires. Also at the same time I replaced the fuel pump relay like someone above mentioned so it could have been either one.
 
FWIW, 22R's had a rubber boot (19114-35011) that went around the dizzy to help keep out water. Not sure if they are still available new, but a quick scour through a bone yard might net you one. Might be worth checking to see if it is large enough to wrap around a 6cyl cap. :meh:
 
Last edited:
22RE's did have a boot. Very sweet feature. Unfortunately not large enough for the 1FZ.

I actually started my off-roading running mini trucks and 4runners.... I just wish I knew a landcruiser like I know them...
 
The 3FE came with a boot as well. Unfortunately the original owner of my truck ripped it. I don't know why he removed it the wires, cap and rotor were all original.
 
well.. the problem apparent did NOT fix itself as its now manifested itself....

I cant drive the thing over about 2K....

The OD light (overdrive) is now blinking at me. I have horrible throttle response... which has progressed from a previous which was just a dead spot between no throttle and minimal throttle...

from doing a bit of searching i believe i'm now actually throwing a code, but im unsure if its the root problem or a symptom of the problem...

any help appreciated... i'm going to do some more searching tomorrow and see if im actually throwing a code and if so, what it is.... thankfully the cruiser did manage to make it back 20 minutes and get me home!
 
next question, can a throttle position sensor affect transmission operation?

I'm still thinking I might have a bad TPS which now has somehow got my overdrive O/D light flashing throwing a trans code... I'm getting ready to go pull the code, so I should know what it is shortly, and will post up.
 
Codes:

Transmission was code 88, severed ECM and TCM or short circuit

Engine code 24, Intake Air Temp Sensor Signal (part of the AFM) short circuit or open for 0.5 sec or more

Engine code 31, Volume Air Flow Meter (AFM) Signal; When idle contacts are closed and the engine speed is 1,500 RPM or less there is an open circuit in the VC and VS signal or a short circuit between VS and E2. (E2 is sensor ground, VS is a connection between the ECM and part of the AFM, and VCC i believe connects the AFM to the TPS via the ECM).

On a side note the TCM does rely on signals from the TPS per the FSM operation description. If the IDL (Idle) points of the TPS close (TPS sees the throttle closed) it signals the TCM to unlock the the lock-up system, however im not sure it recieves the signal in conjunction with the ECM or if the ECM provides it... its looks like its in conjunction, which would me that a bad TPS could signal a bad ECM to TCM connection... but it looks like the signal has 2 ways to reach the TCM, from the VA term of the ECM and from a shared IDL connection from the TPS to the ECM and TCM.

I've already cleared the codes, and I'm going to take it for a spin to see what new codes come up. As it stands right now, I feel fairly confident that its one of these things, listed in what I think is most probable at this point:

1. TPS (Throttle Position Sensor)
2. TPS wiring
3. AFM (Volume Air Flow Meter)
4. AFM wiring
5. ECM
 
Took it for a test drive... just barely got home, again. not cool.

Current symptoms:
First part of the drive had NO issues whatsoever.

Second part of the drive:
While driving it started the whole not wanting to run thing and then threw a tranny code 88 again. got back and checked, no engine codes.

While driving it will just stall, stumble down regardless of throttle input and the catch itself. it barely ran on the way back becuase of this. it would stall, then catch itself, rev back up so i could keep moving, then stall again.

When I got it back to the house its back to its original issue of reving to approx 2200, then stalling, catching itself around 1800 rpms, then repeat. Same thing that was shown in the first youtube video.

I'm still fairly confident i have a throttle position sensor issue of some kind, and the tranny code is just a secondary symptom. In talkin with another very skilled toyota mechanic he agrees with my diagnosis. He had a similar issue where a motor got washed and the throttle position sensor internal spring which helps pull the sensor back to home would bind up and it (the TPS/ECM) couldn't make sense of the throttle position. I'm going to do a quick test of the TPS and see what happens. If it comes back alright, I'm going to pull the whole throttle body off, re-check the sensor, remove, check springs, and lube, reinstall, check again, and reinstall the whole throttle body and see what happens. Hopefully something will become apparent.
 
checked out the tps and afm... both ohm'd out fine.

started it back up, still had the stall at around 2200rpm. shut it back off.

unplugged the tps sensor, and started back up. no issues except a CEL. no stall, hesitation, stumbling, anything... ran great.

Took it for a drive and besides the tranny not knowing when to shift, didnt have a single problem. got back and rev'd it up, no stall. shut it off, plugged the tps back in, started it back up, all the issues returned.

i'd say that means i have a bad tps... but i'm not quite sure how, given that it ohm'd out alright. must be something else going on either inside of it or with the wiring.
 
What year does it say on your plug wires?
 
Back
Top Bottom