HEI conversion....more distributor questions!!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 12, 2005
Threads
24
Messages
234
Location
Prince George, BC
Sorry guys, hopefully this is my last question about ignition systems! :rolleyes:


I have a GM HEI dizzy from a previous failed conversion that I attempted before I became a more enlightened cruiser owner (before I joined MUD :D ). I was lucky with this mod, since the distributor only did damage to itself and not to my camshaft gear.

The HEI dizzy is repaired now, and as I have been looking for an alternative to retarded vacuum and a worn out stock dizzy, I have weighed all the Toyota options and found them all too heavy for my bank account. Then I started looking into a proper HEI conversion and I have decided to go with it.

I checked out this link http://www.geocities.com/calcide/fj402fhei.html
And I did a search on HEI conversions and found alot of information.

What I want to know is which of the methods are the best: grinding flange off, drilling gear etc. Or are these mods meant to all be done together. Pics of modified gears and housings would be helpful, as would some examples of this mod working and being a reliable alternative to a DUI or Toyota unit.

Thanks for answering all my questions so far

Richard
 
Grinding the flange and drilling the gear are meant to be done together. Grinding the flange is to make certain that the dizzy sits all the way down to engage the oil pump, and the toyota gear is because the GM gear tends to "walk up" the pump gear. After these are modified the only real issue is to devise a clamp as the toyota clamp id to large for the HEI shaft.
 
I ground the flange off. Had to make a bushing. Made it out of PVC, but I'm going to have one machined. The "O" ring is important as mine still leaks some oil out of the diz seat. It is a tight fit. I deepened my groove on the diz, but will rework that, too. Performance-wise, it made a helluva difference for me.



Total cost was a set of wires.



Good mod IMO

Ed
 
Could some of the oil leak problems with the ground off flange method be fixed by adding another o-ring groove and o-ring higher up on the part of the housing that goes into the block? I may be wrong, but isn't there an oil passage in the hole that the distributor goes into? the o-ring on the stock dizzy looks like it's higher than the groove on the hei.

As for adding a shim to the bottom of the gear, how much gear is left in contact with the drive gear then?

What kind of damage can you do to your oil pump by allowing it to take the thrust force from the distributor shaft?

If the gear is moved down, does it leave enough of the oil pump drive sticking out?
 
Addressing the "shim" question - Based on measurements from the bottom of the distributor, I still had most of the HEI distributor teeth the same distance from the "Depth control point" (bottom of the clamp or flange (on the HEI). I believe I have good engagement.

Another advantage of the "shim" method is that (most of) the thrust load on the shaft should be taken up by the shim (on the block) and not on the retaining pin.

I don't know about oil pump damage, so I won't comment. It was just an issue raised in other articles.

Good Luck

Rocky
 
Over a year now. Haven't had any problems (with the HEI). If I can only get this darn fuel pump issue solved (of course it would help if I actually spent some time under the hood....)

Thanks -

ROcky
 
This is a picture of the hei unit offered by classic cruisers, and a shamelessly pilfered picture from Rocky's (sorry for the plagerism but it's a good picture)page showing an un modified hei housing. http://members.cox.net/lindahuber/hei_install.html

The classic cruisers dizzy has an o-ring further up, a flange futher up, and it looks like the shaft is shorter too. Does anyone have one of the classic cruiser units? The way they modified them looks like the way to go for me. I've never been able to post pictures before so here goes...
hei_edited.webp
hei2_edited.webp
 
Last edited:
Back
Top Bottom