Headlight Voltage

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 29, 2017
Threads
4
Messages
78
Location
Panama City Beach, FL
I'm swapping out my 60 headlights for a pair of LED's. I always noticed there wasn't a big difference in my Low and High beams and I think I now know why. This is the deal...assuming white is low, yellow is high and green is...these are my meter readings:

battery after 4 hours of dicking around with it - 11.7v

In Low Beam Setting
White/Ground - 11.7
Yellow/Ground - 0
Yellow/White - 11.4

In Low Beam Setting
White/Ground - 11.7
Yellow/Ground - 0
Yellow/White - 11.7

So the yellow white voltage realization was a complete accident but I am thinking is the root. Any help?
 
First off you need a battery. Second, you will find a voltage drop from the back of the alternator to the headlight leads usually and definitely if the vehicle has power running through switches in stead of relays. Check out the link for more than you ever wanted to know. Reference Center
 
Install a relay actuated headlight wiring harness. ARB has a good one. The stock headlight wiring was lame from day one.
 
@slcfj62 builds custom harnesses for landcruiser a. I built my own harness. Day and night difference
 
Find his thread. The diagrams are posted. Anyone can build one.
 
Find his thread. The diagrams are posted. Anyone can build one.

Says you. LOL

I'm really not comfortable with electrical diagrams. I've had other projects with electrical and always seemed to have to send it out. Want to build one for me ???
 
Looking more at the existing I certainly need to just install a new loom and will likely get the arb. That said does anyone have a comment about the .4 volt increase testing across two supposedly hot leads? Makes me wonder if there isn't something more worrisome in my future.
 
The headlight circuit is funky (hard to understand). The FJ62 is even worse. There's the hi-beam indicator on the dash that runs through the circuit too. It could be influencing what you're reading.

I never could really figure it out and most shade tree harnesses don't get the hi beam indicator working (the ARB harness does). It's trickier than adding a couple relays. I gave up on the attempt. With a new harness, the voltage at the OEM bulb connector doesn't matter. Either the relay will close & you'll get full power or it won't and the lights won't work at all. All or nothing.
 
The headlight circuit is funky (hard to understand). The FJ62 is even worse. There's the hi-beam indicator on the dash that runs through the circuit too. It could be influencing what you're reading.

I never could really figure it out and most shade tree harnesses don't get the hi beam indicator working (the ARB harness does). It's trickier than adding a couple relays. I gave up on the attempt. With a new harness, the voltage at the OEM bulb connector doesn't matter. Either the relay will close & you'll get full power or it won't and the lights won't work at all. All or nothing.
Does the arb harness wire all the way back into the turn signal arm bright switch ?
 
It's really simple (dead simple) to connect the ARB harness. It has three relays that will need to be mounted inside the engine compartment near the battery. I put mine in a little wter proof box to keep them protected- but that's just me. They have little tabs that you can screw into the sheet metal.

The harness has three wire bundles. One will connect to the source wire/plug on the driver's side that normally connected to the L headlight. It will plug right into it. No splicing needed. The other two bundles plug into each headlamp - (not using the original plugs). Literally plug & play. The most time consuming part of it is routing the wire bundles neatly to each headlight so that it looks nice & ship shape.
 
No, most headlight harness don't go all the way back to the cab. They use the write from the cab as signal on to the relays and leave the bright light and switch untouched. They allow the high power used by the lights to not have to run back through the cab and the switch and instead takes a much shorter trip from battery to relay to lights.
 
It's really simple (dead simple) to connect the ARB harness. It has three relays that will need to be mounted inside the engine compartment near the battery. I put mine in a little wter proof box to keep them protected- but that's just me. They have little tabs that you can screw into the sheet metal.

The harness has three wire bundles. One will connect to the source wire/plug on the driver's side that normally connected to the L headlight. It will plug right into it. No splicing needed. The other two bundles plug into each headlamp - (not using the original plugs). Literally plug & play. The most time consuming part of it is routing the wire bundles neatly to each headlight so that it looks nice & ship shape.
There are two different harnesses out there. One appears to be just a loom replacement and the other has relays and all. Neither has even a short useful description anywhere, including the ARB site. Any help there?
 
The ARB harness comes with an instruction sheet but it's very simple to hook up without it. You're just plugging plugs into each other.
 
get the relay version. they will simply plug right into your existing headlight plugs at the cowl.
 
Back
Top Bottom