Head swap

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 6, 2007
Threads
120
Messages
1,755
Location
Under the hood
I may need to pull the head on my '93. I have a spare engine from a '94 in my garage.

If I rebuild the head from my '94 and set it on my '93 will I need to adjust my valves?

Sorry if this is a remedial question - I don' understand the valve adjust on the FZJ at all.
 
no you don't have to if your not swapping cams but it would be a good idea to since the head will be off and itll be easier to do it out of the vehicle. if youre swapping cams then yes you will have to do an adjustment

valve adjustment is a shim over bucket and to adjust the valves you swap in different shim thicknesses to get the correct lash. there is a sst to depress the spring and bucket and you can fish out the shim with a magnet. https://www.amazon.com/Zdmak-Valve-Tools-Some-Toyota/dp/B013GRHHI6/?tag=ihco-20
 
Rebuild the head = you're adjusting valves.

If you just swap a complete head & it was set correct prior, then no need beyond a doublecheck.

Any head swap I did I'd want new valve-stem seals automatically. That's just me.

The decision is if you want to do a real head rebuild/ machine it, or just swap the complete head you have & not touch anything.
 
The decision is if you want to do a real head rebuild/ machine it, or just swap the complete head you have & not touch anything.

The idea is a full head rebuild in advance of the tear-down. Then I can drop the new head onto the engine as soon as I take off the old one with minimal downtime.

My '60 valve adjust was a piece of cake, I'm nervous to drop the '80 head on and then be missing a flurry of shims and stalled out anyway.

Can the shimming be done by the machinist, or does it have to be installed on the truck to do it correctly?
 
Yes have the machinist do the valves and stems , change gasket drop it on.
 
If by rebuilding your head you mean having your local machine shop grind the valves, and seats. Then yes, once they remove metal from the valve face, valve seat, or replace any bad valves you now need to check your valve clearance, and adjust with shims. Remember since you have 2 heads you might be able to mix, and match valve shims between the two heads to set your clearance, without having to buy any new shims from the dealer. Below is a list of factory Toyota part numbers for the different shim thickness.
 
I'm nervous to drop the '80 head on and then be missing a flurry of shims and stalled out anyway

if your head is spitting out shims while your driving than you have way bigger problems. the shims sit in the bucket and will not come out unless they are removed by someone and its very noticeable when the shims arnt in the bucket.
 
no you don't have to if your not swapping cams but it would be a good idea to since the head will be off and itll be easier to do it out of the vehicle. if youre swapping cams then yes you will have to do an adjustment

valve adjustment is a shim over bucket and to adjust the valves you swap in different shim thicknesses to get the correct lash. there is a sst to depress the spring and bucket and you can fish out the shim with a magnet. https://www.amazon.com/Zdmak-Valve-Tools-Some-Toyota/dp/B013GRHHI6/?tag=ihco-20
Does not work with Land Cruiser 1993-1997 and Lexus LX400 1994-1997<------ this was on the amazon page near the bottomin the product info. found this listed below>https://www.amazon.com/Schley-Products-88250-Adjusting-Toyota/dp/B0014DF1AG/ref=pd_cp_263_1/136-2769713-6862358?_encoding=UTF8&pd_rd_i=B0014DF1AG&pd_rd_r=ZGGJQM5EJWSRNX4FS3ME&pd_rd_w=3uV8o&pd_rd_wg=Z73B2&psc=1&refRID=ZGGJQM5EJWSRNX4FS3ME check and it said it would work on the 96 lx450. Hell I don't know they look the same to me.
 
Last edited:
no you don't have to if your not swapping cams but it would be a good idea to since the head will be off and itll be easier to do it out of the vehicle.

Maybe a better question would be: can I adjust the valves with the head out of the truck? This reads like yes, but I know in a 2F that would never work because of the pushrods.
 
Yes have the machinist do the valves and stems , change gasket drop it on.

+1

This is what I paid for & had done. Dropped off my head @ shop & a bag with stem seals, had them check flatness & cleanup, do the valve seat grind, new stem seals in & adjust valves - the standard "full service" job they do.

$$$ of it varies, but it was a $500 job ~decade ago.

Maybe a better question would be: can I adjust the valves with the head out of the truck? This reads like yes, but I know in a 2F that would never work because of the pushrods.

Yes for the 1FZ head.
 
Maybe a better question would be: can I adjust the valves with the head out of the truck? This reads like yes, but I know in a 2F that would never work because of the pushrods.

yes you can, it would be easier on the bench than in the truck.
 
Back
Top Bottom