Head is off.. thoughts and ?'s

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 8, 2004
Threads
45
Messages
1,044
Location
Houston, Texas
Well, sweet coolant smell in the exhaust, bubbles in the overflow and much higher oil consumtion than normal....and the head gasket looks good. There are signs of deterioration around #6 but very minimal. What i was most surprised by is the amount of carbon build up in the intake and on the top of the cylinders. So here are my questions:

1. Since the gasket looks good, could that meen a cracked head or block?

2. How much harder is it to remove the lower intake now that is hanging off to the side?
2.1 My thoughts were to take the intake into the machine shop and have them cleaned. If doing this, do I need to remove anything from the intake, both upper and lower, before taking them in?

3. The injectors are going to RC Engeneering. Do I need to number the injectors 1-6 so they go back in in the same order? Does it matter?

Thanks,

Buck Buchanan

PS Pics will come tonight :cheers:
 
Buck, do you have black build up on the firing ring area? it will be interesting to see the pic's. I would guess that you have some problems you are not trained to see. Any how looking forward to seeing the Pic. I have not seen a internal crack in the cylinder areas yet on a 1FZ, and only Dougs cracked head in the valve train area, been the only cracked head. I would bet it is the gasket.

#2 you will need to pull the wiring from the computer through the fire wall and then unbolt it from fire wall. Pull it though the intake manifold. Yes you will need to remove all the stuff from the manifolds to have the machine shop clean them. Best is if they soak them in solution over night.
If you have not sent them in yet, a cheaper place is WitchHunter Performance - Injector Cleaning & Flow Testing Services In washington state. They do the same job and are real quick in the turn around time, supply you with a before and after sheet(just like RC). I have been using these guys for several years now, I am not afliated with them nor do I get any kick back on stuff I send in to them for refering.
good luck, Robbie
 
Buck,

Congrats! You are half way there!

1. When I got down to the gasket I had no idea what I was looking at. I expected a very obvious deformation in the head gasket. But CDan inspected the gasket and concluded that it was a typical failure.
2.To remove the lower intake you need to address the harness that runs through it. Riad replaced his wiring harness and said that accessing those connectors wasn't too bad. Onur took his upper and lower intakes to a machine shop for cleaning. They came back looking brand new. If you have picked out a shop for the head ask them how much they would want to clean intakes and the valve cover. All they really do is throw it into a industrial dishwasher. I recommend removing everything. Leave nothing attached to the intake, head or valve cover. That way nothing will be lost by the machine shop.
3. The numbers only really matter for record keeping. RC will give you a before and after test results of the injectors. When it comes time to reinstall the injectors the order doesn't matter because they will all be flow matched.


edit:

doh... Robbie is a faster typer than me
 
Buck, do you have black build up on the firing ring area? it will be interesting to see the pic's. I would guess that you have some problems you are not trained to see.

Is the firing ring area right around the upper part of the cylinder? If so then yes. There is build up in this area. As far as problems I'm not trained to see, that is the understatement of the year. I know absolutely squat about engines. All I have done is look at the fsm, watched the video and asked questions here. Again, I figured the worst that could happen is I get to know my truck better and if I screw something up, have it towed to someone who can fix it or fly Robbie down :D.

Thanks,

Buck Buchanan
 
I was trying to get pictures posted last night and this morning with no luck. I'll work on it again this evening. If someone would be willing to post em up for me just pm your email.

Sorry for the delay

Buck
 
buck,

A great way to post pics is www.photobucket.com

you load the pics to that site and paste over the html link and the pictures show in the thread. very easy and you have no limit to size or amount of pics you can post :D
 
You doing this all on your own ?

I would like to see pictures as at this point if mine were to go I'd be more likely to have it done than anything else, especially given that it either would block part of the driveway, or the entire garage while down ....:doh:

Maybe a better question is when you will be reassembling ?

Perhaps I could get over there & spin a wrench or two and do some serious eyeballin' at the same time ! ;)

Britt
 
Britt,

No problem. The head goes to the shop tomorrow and I should have that back about Thursday. The wrenching will start on Friday evening. Hope to button her back up on Saturday, Sunday at the latest.

You are more than welcome to lend a hand or stop by for a look see. If you do come by, remind me and you can have some spare drive flange studs.

Come Hell or high water the pics will be up this evening.

Buck

Romer edit: Added pics for Buck
#6 cylinder1.webp
#6 cylinder2.webp
#6 cylinder3.webp
 
Last edited by a moderator:
two more pictures for Buck
#6 cylinder4.webp
#6 cylinder5.webp
 
Thanks Romer. My biggest headache since starting this hg has been trying to post photos.

Buck
 
Well buck, it looks like you were sealing against the head real well, but the block side post #9 pic 3 is looking real nasty. The pic is not the best, but it looks like carbon build up on the upper right of the cylinder and nasty black at the upper left of the cylinder. Flip the the gasket and take a couple pics and so we can see the side that seats against the block. How is the rest of the cylinders.
If some one can pull up a old thread by turbo crusier, you can see what it should look like when it is clean and ready to put back together Buck. This take a couple of 2-3 hours of teadius work. But is work it to get rid of the carbon build up on the cylinder wall and the pistons.
Any how I see a bit of ring groove wear. What kind of fuel do you use? Grade of Fuel? Just info for my knowledge base. How many miles on the engine?
 
Well I look for turbocruiser thread and found Romer thread from 06 when I gave him pics. The first post is pics of the before and after cleaning. Will give you a Idea what is possiable with a little elbow grease. Turbocrusier has a thead some where as well with some good pic's. Personally if you do not get it as clean as this you risk scoring the cylinder wall and hot spots that can cause predetonation. I know other techniques are tought, I jsut did not learn that way. Good luck Robbie
 
Well buck, it looks like you were sealing against the head real well, but the block side post #9 pic 3 is looking real nasty. The pic is not the best, but it looks like carbon build up on the upper right of the cylinder and nasty black at the upper left of the cylinder. Flip the the gasket and take a couple pics and so we can see the side that seats against the block. How is the rest of the cylinders.
If some one can pull up a old thread by turbo crusier, you can see what it should look like when it is clean and ready to put back together Buck. This take a couple of 2-3 hours of teadius work. But is work it to get rid of the carbon build up on the cylinder wall and the pistons.
Any how I see a bit of ring groove wear. What kind of fuel do you use? Grade of Fuel? Just info for my knowledge base. How many miles on the engine?

I use regular unleaded. Normally fill up at a Texaco. The tops of all the pistons have a good amount of carbon build up as well as the intake. I will tae some pics of the underside of the gasket as well as the rest of block.

History- The truck has been extremely well mantained, has 188k on the clock. RT temp guage mod and the temp has never risen above halfway. New oem 3 row brass rad, 6k fluid in a blue hub, No synthetic oil change over 8k miles with most at 7k.

There is one mod that may have a bearing on carbon build up, the Greddy catch can. There was a thread about 2 years ago about whether or not it worked as well as it should. As an example when I drove to Moab from Houston and then wheeled, could I have built up a bit in the resevoir and then splashed into the pvc hose?

What is ring groove wear?

Thanks Robbie,

Buck
 
Well ...

Do you get the head back today ?

Still trying to see how things shake out - in theory, Sunday is tied up as we were going to look at a 1st Gen 4 Runner, but if it's sill good to go on Saturday, life is good.

:confused:

let me know if you are still in need of, or up for :bang: company.


Later !


Britt
 
Well, a couple buds came over and helped me work on it till 4am this morning, held my breath and cranked her up. She idles dead on at 650 rpm with the timing set to 3 tdc. Engine sounds good.

HOWEVER, I turned on both heaters and no hot air. I have air blowing but not hot. I turned on the ac and the compressor did not kick on. I also don't feel my coolant is circulating as it should. The water pump never seemed like it kicked on to circulate the water. I double checked the heater valve and it is functioning correctly. (when ac on and slider moved to cold the cable is fully extended to move the valve lever to the stop)

While letting it idle, the modified temp guage rose to about 1/3 where it normally stays. The water in the radiator did get hot but I couldn't see it circulate. No leaks that I could see but I was pretty wiped by that time. As far as the water circulation, I may have been paranoid, well no maybe about it I'm paranoid, and didn't give it time to get hot enough to circulate.

Any and all thoughts would be appreciated.

Buck Buchanan
 
Good question Rookie. I did not remove the t stat for the hg repair. I did wonder if a piece of debris is clogging it or has impeded it from closing. I thought I might pull it tonight and test per the fsm.

When I replaced the t stat last year I did put the jiggle at high noon.

Buck
 
Back
Top Bottom