Group Buy -- OEM 80 Series Hand Throttle

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

OK got mine in took like 15 minutes.because I couldn't find my flashlight. Then the PO had a bunch of cabling in the way (GPS and Sirius), then I had to adjust the throttle cable (had it a bit too tight. Was idling at 1800).

If not all that...yeah like five minutes
 
Got it in. Easy as pie.

FYI.... The white stripe in the knob end of the cable goes up, for the knob to be orientated in right side up.

Sent from my iPhone using IH8MUD
 
Got mine. Just like the last few posts, easy to install, needed a flashlight, almost knocked over my beer... Almost. Got it to idle just over 2k, no use for it now, but future plans and the neat-o look-what-I-have factor made me buy it.

This didn't count as a project/job because I didn't bleed. Was too easy.

Thanks Yan
 
Last edited:
Got mine today! Will install tomorrow.

Thanks again!
 
Akella said:
Paper work was done for the shipment, so it should get on a plane soon.

It should be here Monday or Wednesday.


The following people PLEASE PAY ASAP otherwise when shipment lands in Canada i will just throw your sets for a grab on fist PM basis or to the next person who prepaid their set.


128 LINUS
131 Galandcruiser97
135 C5Drvr
142 davegonz
146 GCRad1
147 drom68




NEXT 7 people in line please pm me if you are active and would like to prepay your set. In this case you may get very lucky and get your set from this shipment if some people will miss on a payment. Or worth come to worth i already have 4 sets purchases overseas and you will get it in next shipment.

NEXT 7 people who can pm for the prepay:

148 Dark Star
149 winstonclein
150 darasick
152 TX Silver
153 FastCarGuy
154 cruisinrock
155 jjuan


:cheers:
Click to expand...
I'm number 148, payment sent.
 
winstonclein said:
Can someone tell me how to pay Akella?
I'm kinda lost and I cannot find his paypal address (email) to send payment. If you want send me pm.
I appreciated.
Click to expand...

Send him a pm and he will pm you back with the Paypal info.
 
Would love to be added to the list if possible.

Buck
 
Add Me!
 
Kernal said:
Anyone have some photos of the install process they can post up?
Click to expand...

Went to fast to take pics.

Partially remove the bottom of the dash.
Feed the through the hole in the dash. (as mentioned white side up)
Connect the white plastic clip at the rear braket.
Connect the black plastic holder in the bracket forward a couple inches.

I just had to slighty adjust mine. Idle not changed, and floats at 2k when engaged.

From Slee instructions:
http://www.sleeoffroad.com/installation/ht_install.pdf

It will all make sense once you stick your head in there.
 
I've been chosen! PM sent!!! WoooHOOO!! I'm #146!
ToyStory3Wallpaper9800.jpg
 
retrofive said:
Went to fast to take pics.

Partially remove the bottom of the dash.
Feed the through the hole in the dash. (as mentioned white side up)
Connect the white plastic clip at the rear braket.
Connect the black plastic holder in the bracket forward a couple inches.

I just had to slighty adjust mine. Idle not changed, and floats at 2k when engaged.

From Slee instructions:
http://www.sleeoffroad.com/installation/ht_install.pdf

It will all make sense once you stick your head in there.
Click to expand...

Floats at 2k when engaged? I don't follow. I installed mine the other day and I can set it for any RPM from 1k to almost 3k if I recall correctly. Pull it out to the rpm I want and turn it to the right to lock it. Or am I using it wrong? Someone enlighten me, please?
 
You must log in or register to reply here.

Share this page

Back
Top Bottom