ghost in the machine!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 22, 2003
Threads
106
Messages
1,018
Location
Silicon Valley
Lately I have a hard starting problem, yesterday I couldn't start the fj40 at all and left the key in the "on" position and talked to the mail man and cleaned the tools around the truck and the truck just started itself and engine ran...This freaked me a bit because fortunately I had the tranny in neutral not in 1st like usual (transfer case was in low)...I could have been ran over by my own truck or it ran into the house.

I think the ignition switch is bad, what do guys think?

Btw, the weekend before my brother told me a story of his friend was killed when she was ran over by own her car in the driveway...

Thanks in advance.

/td
 
Last edited:
I just don't leave the key in unattended anymore, the truck is always in neutral right now...When trying to trace the wires I found a short that I have been looking for sometime thanked to woody's technique of removing the fuse one by one...So there no short any more but something goes amok with the ignition circuit.

Btw, the starter does work but engine just doesn't run.
 
Any one familiar with MSD???

Ok, after 2 hours of troubleshooting I narrowed it down to this, when the key is either at "ON" or "START" there's no current at the coil, so that's why there's no sparks.

Here's my setup, MSD Offroad 6, with a variant of Pertronix Ignitor, and Flame Thrower coil, this setup worked perfectly for about 2 years, it used to take only 1 crank to start the engine...Until I took my truck apart for the SOA...Upon putting it back, it ran for couple times than now, when I crank, the engine does turn over but does not fire.

Is anyway I can verify that my MSD is working correctly?

My setup is exactly like this diagram, when I put volt meter at the positive and negative at the coil, and turn the key to either "ON" or "START" there's no current:

http://www.pertronix.com/tech_support/assets/msd6series.pdf

I did verify that there is current at the "Heavy Black" and "red" wires in the diagram when the key is either "ON" or "START"

Anyone familiar with MSD here??? I got couple thousand miles out of this MSD Offroad 6 box it's hard to beleive that it's bad.

Thanks in advance
 
mustardfj40 said:
Ok, after 2 hours of troubleshooting I narrowed it down to this, when the key is either at "ON" or "START" there's no current at the coil, so that's why there's no sparks.

I put volt meter at the positive and negative at the coil, and turn the key to either "ON" or "START" there's no current:

I did verify that there is current at the "Heavy Black" and "red" wires in the diagram when the key is either "ON" or "START"

There is no voltage (or current either) across the + and - sides of the coil with the key on or off because there is no circuit until it it time to make a spark.

There should be a voltage from the + side of the coil to ground with the key on and no voltage between the - side of the coil and ground.

If there is a voltage at the + side of the coil, if you momentarily ground the - side, you should get a spark out of the coil HV line if the coil is good.

Do you get a spark when it is cranking?

The wierdness is probably a short at the ingition switch or in the wiring harness between any key on hot wire and the starter solenoid wire. If so, it should happen when you are driving it too.
 
Nomis said:
Yeah that would leave a mark - let us know what you find. And be safe. Of course if it mows down a Jehovia's Witness - you would have an alibi.
I could never be a witness as I never saw the accident.
 
OK guys, that's funny.

Charlie, thanks for pointing that out. There is no sparks now when cranking

When measure the voltage off the redwire (switched positive from the ignition key, I got about 12.5 volts, but during cranking the voltage drop to only 7.5 volts. Is this too low? I did some research on the MSD and the box shutdowns the redwire (the one to switch ignigtion key) when voltage drops bellow 9-10 volts.

Found some good info on the net regarding how to test the MSD unit, will try it later when I get home.

/td
 
7.5 V may be too low for reliable starting. Do you have the black wire with yellow strip that goes from the starter to the coil+ and the ballast resistor? Try temporarily running a wire directly from the battery + to the coil+ to see if this helps with starting. If so, you may have a high resistance/corroded connection somewhere between the ignition switch and the coil. I don't know if that is going to help if the MSD box has some voltage sensing function. You could also try bypassing the key wire by jumping from the battery + to the small red wire that goes to the MSD. anyway, the idea is to bypass the key circuit to your ignitor coil to see if the main feed from the key is bad.
 
Charlie, you're tha man!!!

First, I verified the MSD box was ok, then I followed your suggestion and wired directly from battery to the + of the coil, it didn't work, finally I wired the small red wire of the MSD box directly to the + of my second battery (which is islolated from my main battery with an isolator)...And it fired up right away with only 1 crank!!!

So some connectors are getting corroded somewhere...I also have the Cifford alarm installed from the PO, after all this I learned that the alarm is pretty useless, only scares little kids, I am thinking about ripping it out.

Since my truck is a '75 it had a ballast registor in the ignition circuit, after replacing my original starter with a new OEM FJ60 starter, the bypass wire was not connected anymore and I stop using the ballast registor.

Here's to help other dudes from ever to test their MSD boxes for damage, taken from www.techwestracing.com:

"First you will need a Volt/Ohm meter (this check can be performed with an analog or digital meter as well). The type of meter will not change the outcome of the test performed. Set your volt/ohm meter on the 1k ohms scale, then position the MSD®Ignition in approximately the same orientation as mounted in the vehicle. This is done to ensure that the MSD®Ignition is relatively in the same position as when the failure occurred. Next take either lead and attach it to a bare metal area on the MSD®Ignition. The second lead needs to be hooked to the Large Red wire that provides your main 12vdc input. In an Undamaged MSD®Ignition the needle will stay in the home position (ie. max Ohms for scale chosen). A Damaged MSD®Ignition will show a reading of 3k ohms or lower."

Thanks! Learned so much about the Ignition in my FJ40.

/td
 
"One test is worth a thousand expert opinions" - Riehle axiom

It is too early to gloat because you still have to find the problem with the ignition feed. Hopefully it will be something easy, like the wire end because you have to be Houdini to get under the dash.
 
Some update

My boy is graduating so we're busy with parties....But I managed to get couple hours working on the truck. I tested the ignition switch which is ok and found out that I have a short in the ignition circuit!!! Applying the pulling out the fuse trick, I found that it's somewhere in the heater circuit...More troubleshooting ahead. If you have any tips please feel free to help. Thanks in advance.

Btw, here's a picture of my truck this morning, with SOA, All Cruiser disk brake, Butch Lewis style Saginaw/SR....Can't weld and want to do SOA/SR/Saginaw professionally? I'll do a write-up later.

after-soa.jpg
 
mustardfj40 said:
I tested the ignition switch which is ok and found out that I have a short in the ignition circuit!!! Applying the pulling out the fuse trick, I found that it's somewhere in the heater circuit...More troubleshooting ahead. If you have any tips please feel free to help. Thanks in advance.

Nice looking truck.

This sounds a little strange, in the sense that it is difficult to imagine how a short in the heater circuit could effect the ignition circuit unless the short was from the ignition wire to the heater, in which case the heater would come on when the switch was off. If the short in the heater circuit was significant to cause a voltage drop, the fuse would just blow.

The ignition wire is one of the few circuits that is not fused and is is a bit of a double edged sword. It can tolerate a minor short without blowing a fuse, so I guess Toyota thought that this was better than losing power while driving. The down side is if you have a big short, the wire will fry. Mine was fried by a PO and it took out some of the other wires in the same harness. The ignition wire is big enough that I would have thought that the fusible link would burn out first, but it melted the ignition wire instead.

Check for rubbing wear at places where the harness crosses the chassis and hold down strips.
 
I think I may read something wrong then. I was using this diagram in the debugging process:

http://www.ih8mud.com/tech/fj40_wiring_diagram.pdf

Beside going to the igniter, the ignition circuit also go to the fuse box and heater fuse is one of of fuses, this heater circuit also runs the gagues, back-up lights, brake lights.

Also just found out that one of turn signal relays stops working.

Thanks very much.

/td
 
It is a useful diagram, except for the Acc and Start wires at the ignition switch are flipped.

Basically, all I meant to say is that usually the problem with ignition circuit shorts is that the short is upstream of the fuse; otherwise the fuse would just blow.

What turn signal relay? I didn't know that there was even 1 of those.
 
I meant the flasher. Charlie, I see what you mean, will do some more trouble shooting. Thanks.

/td
 
Final updates

I spent couple hours here and there and 3 weeks ago found another short at my brake light switch which I caused couple years ago at Moab when I simply twisted the switch to adjust it, the terminal wires got twisted toghether and shorted out, a new Toyota switch solved that issue.

But the main problem was the ignition switch, the inside got corroded and it was cleaned up by the PO and he lost 2 little springs, and one of the wire was bad. I replaced the ignition switch a brand new one from Toyota (costed 50 bucks)...And now my truck starts up with only 1 crank like it used to.

To sum it up, my truck suffered triple failures: 2 electrical shorts and a bad igntion switch. Thanks to everyone who helped out.
 
Back
Top Bottom