gears vs. SC

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I have the SC, stock gears and 285's with a non winch ARB. Made a huge difference in how it drives. I live up in the Blue Ridge Mountains (Hills) at about 3200 ft. Couldn't imagine driving it without the SC. We can barrel up and down the Blue Ridge Parkway without any appreciable effort.

I was way under 10K for the install. I did the head gasket, valve job, cleaned the injectors, ceramic coated the exhaust manifold. Replaced the seals in the oil cooler and o ring at the distributor. All new hoses and belts, new fan clutch, new water pump and cleaned and flow tested the radiator. About $2k in labor plus parts.

My only problem thus far is the silver paint on the SC is cracking and flaking off.

With the SC - still get 12 mpg day in and day out - but now have to pay for 93 octane.
 
I have the SC, stock gears and 285's with a non winch ARB. Made a huge difference in how it drives. I live up in the Blue Ridge Mountains (Hills) at about 3200 ft. Couldn't imagine driving it without the SC. We can barrel up and down the Blue Ridge Parkway without any appreciable effort.

My only problem thus far is the silver paint on the SC is cracking and flaking off.

Obviously you are driving too fast :flipoff2:
 
Aside from the swap talk & back to original question - since you have factory lockers, you should pay to get the gears done, the open diffs a good mechanic can do, but the e-lockers are a little more complex & the shim pack alone can cost you right into what would be labor at a good shop - Slee isn't too far away, so a little road trip for gears would put you into whatever you figure the cost to be once you call Christo & see what the charge would be, then the cost of there & back.

As for a supercharger, if you are fairly comfortable with toolset & have the time to do it, the instructions they include are really straightforward, so you could do it yourself - but I would make sure your motor has a updated headgasket, otherwise it'll be a house build on a shakey foundation. So really ~$3300 for the charger, but add another ~$1500 for parts & getting new stem seals in the head (will take care of any oil useage if you have any)

I'd do the gears first, as that makes any tire size you want to play on a possibility without drivetrain strain. Skip 4.56's - they aren't worth it as the jump isn't much - I have 4.88's & they aren't all that much either - I really wish I jumped to 5.29's - but then unless you want to run 35's minimum they are a bit much.

I personally did gears first, and my supercharger is still waiting to install. I'm buying a 2nd 80 that has airlockers & 5.29's right now, so the fan can wait until I get the new one all PM'ed.

Gears. and it'll be a good ~$2K+ buy the time all is done & you are spinning rubber again.


Sorry for the question, a newbie here. I live in the Houston area, I will not be doing crazy rock crawling. More expedition and camping out in west Texas and New Mexico, and maybe the the transatlantic trail(some day)
Will be doing the 2.5" lift. Kinda want to stay with 33" all the way around, am also converting a M1101 military trailer into my off road trailer ( that's a project I it's self)
The biggest tires I will ever run is a 35", which I am starting to consider after reading to this forums.
Sorry for the long winded reply, but kinda of wanted to let you know what I will be towing and doing with it.
So I was thinking on the 4.56 gears but now considering 4.88. I want to be able to run 65 to 70 mph to the interstates pulling the trailer. So a supercharge is also on the list.
So I guess the question is 4.56 will not be enough. And the 2.5" lift with 33" is that to much?
Thanks for your time.
 
I have a 7000 pound fat truck with all our gear, front and rear bumper, custom skids, custom storage, sliders and big roof rack, lifted four inches, with 35's and 4.88's and m101 trailer with RTT on 33's . Cruises 75 on gently rolling highway all day no issue. It can pass but I have to plan it. I have no charger.

With no trailer, I can pass pretty much anytime I want. Its a little slow on long ascents but I can hold speed and I live in coastal mountains
 
I have a 7000 pound fat truck with all our gear, front and rear bumper, custom skids, custom storage, sliders and big roof rack, lifted four inches, with 35's and 4.88's and m101 trailer with RTT on 33's . Cruises 75 on gently rolling highway all day no issue. It can pass but I have to plan it. I have no charger.

With no trailer, I can pass pretty much anytime I want. Its a little slow on long ascents but I can hold speed and I live in coastal mountains


Okay THANK YOU!!!!
So forget the 4.56 and just go with the 4.88, I was just worried about not being able the run 70q mph down the freeway.
So I am also going to install a supercharger down the road and should be good to go. But reading this post "Linus" posted that I would have to install a new head gasket. So next question would I have to install a new head gasket with only having 113k miles on my engine?
I bought two LC to make one awesome looking and working. So on this note I am going to pull out the engine with 113k miles and install it in the other LC, so while I have the engine out do you think I should replace the head gasket, and if so do they make a certain head gasket that superior to others?

THANK YOU !!! For you reply
 
If the motor is out there are a number of easily done PM tasks. Throttle body clean, injector clean, PPH replacement, fuel filter replacement. VSV replacement etc

I personally wouldn't bother with the head gasket, or vsv until it needs it.
 
Or injector clean either unless you're pulling the head
 
I'm just going to slap a turbo on mine and report back. I like the idea of keeping stock gears because it would be easier to bring back to stock in case of an accident/part out/sale. I also like the idea of being able to run cheap 265 winter tires or 315 summer tires. Not to mention saving the cost of re-gear. Who knows, I may decide to re-gear anyway, but I'm trying the FI route first to see how I like it.

:edit: I also don't really see the merit of HG as PM unless you have reason to believe yours is going. Just seems like a lot of money for a "maybe" scenario.
 
My comment on the HG is because the 1FZ saw a different HG design once enough people complained - either really check the overall health of yours (far more realistic) or just change it.

If you can do yourself, it's a hell of a lot easier to do in your driveway pre-overheating than on the road after an 'event'.

I'm not for just changing it for no reason, but if you're adding boost it's something to be aware of - the original gasket design was changed. You choose what to do with that information.
 
Back
Top Bottom