Fuse pannel, what is what!!@*#@

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 25, 2005
Threads
29
Messages
132
Location
Huntsville,Tx
Ok I know that you are going to laugh...but I will take it like a man...
I have a 1977 FJ40 the fuse pannel sometime ago I lost it.
I am now having trouble with my brake lights.

I have changed the brake switch...worked thought it was fixed, patted me on the back...NO it is not working (fuse?).
Hence my Question
can someone show me or tell me which order the fuses go in. I have a stock fuse pannel (not dicked with).
Thanks Dennis
 
There isn't a fuse for the brake light? hhmm.
Hope someone knows what the problem is...somthing ya just gota have (brake lights)
thanks
 
I was also thinking ablut changing my fuse pannel to blade fuses. Any sugestions on what to buy? (not an electrical genous) or speller.
 
Denofearth said:
There isn't a fuse for the brake light? hhmm.
Hope someone knows what the problem is...somthing ya just gota have (brake lights)
thanks

"horn stop" - This is the brake light fuse.

Is the switch stuck? I had one that would not turn off, but that was because the little rubber pad on plate that engaged/disengaged the switch plunger had fallen off, so the plunger was never fully actuated by the pedal.
 
If it has ever seen deep water check the bulb contacts for corrosion or the connectors. Does the horn work? If not ry to clean the fuse holder with a brush. Be sure to disconnect the battery first. Do you have a meter or test light? That can be helpful. If you have power at the fuse and not at the lights start working your way in.

Good luck
 
well I tried. I think the new switch from Hi-lo Orileys is not the right one. I took everything apart and you can hear the switch click some times when you push the pedal in and not sometimes. The horn does work and I traced the power and it is good to the switch. Should I order a new switch from...toyota (ouch)!
 
Denofearth said:
I was also thinking ablut changing my fuse pannel to blade fuses. Any sugestions on what to buy? (not an electrical genous) or speller.

You could try something like this... Parts are from www.waytek.com. The panel sits where the old heater was, and has a cover that snaps over it. Of course it changed a little as I finished the wiring (more relays...ECM hookups, etc...)

I'm no electrical genius either, that's why everything has to be laid out understandably and done clean...otherwise I'll never figure it out...:rolleyes:

-Lil' Ricky

:cheers:
image0006.webp
 
HawkDriver said:
That looks super clean and easy, I too hate wiring messes. So where's the heater?

No heater. Its mainly a trail truck, and in Texas with no top or doors you either don't need a heater cause its already too hot, or it is too cold and no heater will be of any help anyway.
 
LilRicky said:
You could try something like this... Parts are from www.waytek.com. The panel sits where the old heater was, and has a cover that snaps over it. Of course it changed a little as I finished the wiring (more relays...ECM hookups, etc...)

I'm no electrical genius either, that's why everything has to be laid out understandably and done clean...otherwise I'll never figure it out...:rolleyes:

-Lil' Ricky

:cheers:

So did you rewire the whole cruiser? Or just re-did the panel?

Thanks, Chuck
 
CruisinTiger said:
So did you rewire the whole cruiser? Or just re-did the panel?

Thanks, Chuck

For the most part, it all got rewired. New gauges, switch panel, all the motor wiring was redone for the TBI, etc. I think there is a small section in the column that I did not replace...:D

It sounds like a huge deal, but really its not that complicated. We are not talking about a modern vehicle with a hundred circuits, here. In fact it was easier for me to rip 95% out and start over than it was to try to adapt the old wiring to all my changes.

-Rick
 
Back
Top Bottom