Front end problem/ Sloppy Job

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 19, 2006
Threads
62
Messages
212
Location
Hot Springs
I am glad I said charge it, I took my 74 FJ 40 in for new tires, I used the trailer to haul it in , and the tire shop must have overlooked this, I had 31x10 placed on it, and when I got back home and unloaded it, it seemed the brakes were draging, well there not, what do I need to do to correct this, cut the arm and shorten, ? I guess its good there closed today and tomorow, :mad: and am I right in thinking that this is there screw up and not mine, they should have seen this before letting the vehicle leave there shop? So they need to replace both front rims, since there is a nice groove on the inside now.
DSCN0034 (4).webp
 
Even with the correct backspacing, aluminum rims have a thicker rim and will rub exactly where you are having a problem. What will, or did for me, solve it is some 1/4" aluminum spacers, the drawback being that you have less engagement of the actual lugnut and they need to be re-torqued several times to prevent loosening.
GL

Ed
 
razorback,
Do you have any specs. on those rims, like offset?
If your stuck w/those...you may have to run spacers to clear TR Ends.

Looks like that particular offset is one to avoid...
 
the web site for the rims show a offset of -48 and a backspacing of 3.63, as to be stuck with them, I will pay for the tires and 2 rims and I feel the tire shop should have to replace the front rims, since there in that business, and it should have been noticed by the shop.
 
I think 3.5" is the correct backspacing for a '40. But as I mentioned in my earlier post, the thickness of an aluminum rim will fawk you every time. 'Specially with drum brakes.:frown:

ED
 
I agree. I busted tires for about 2 years. Anytime aftermarket rims are used they should check the spacing. What if the interferance had been greater and the rim didn't seat properly? or what if it was able to take enough material out of the rim to cause a failure? Could have been worse. Additionally, the manufacturer should know what rims fit on which vehicles. It's easier to just send em out and make note when they don't fit, but by now they should know what it takes to fit on an fj40.
 
I tell EVERY customer that I talk to that is going rim shopping 3 things:

1. Stay away from aluminum.

2. Most tire shops don't know jacksheit about landcruiser issues, so......

3. Tell them you want to 'test' one rim on the front axle [doesn't matter to me, drum or disc] BEFORE YOU buy. If they have any objections, start looking for another shop.

Good luck.

Mark A.
 
I think 3.5" is the correct backspacing for a '40. But as I mentioned in my earlier post, the thickness of an aluminum rim will fawk you every time. 'Specially with drum brakes.:frown:

ED


Mark, the reason I made the distinction between drum and disc is that when I changed from a '66 drum axle to a '77 disc axle, I had no clearance problems, even with the aluminum wheels. Did not have to use spacers.:confused:


Ed
 
Later Problems

You might want to think about having all 4 rims replaced. When you rotate your tires ( if you move them front to back ), you'll be right back to the same problem 'ya got now, TRE rubbing. Just a thought, Al
 
Those look similar to mine. Mine are 10" wide and have clearance isues. I have 1/4 inch spacers on the front and it clears. Tire rotation is no big deal because you leave the spacer on the fronts when you rotate. The lug nut engagement is a serious concern though. With the al rims and the spacer you don't have very many threads to catch. If you keep the rims consider getting longer studs, the part number is here on MUD somewhere. I'm considering going back to steel with some beadlocks to minimize wheel stud concerns. Good luck.
 
Back
Top Bottom