Front end clunk need advice

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 9, 2006
Threads
73
Messages
630
Location
Okinawa Japan
I am hoping someone can give me some advice on what might be wrong with my front end.

First of all I have read and performed every step in the "
Front axle evaluation for FAQ" thread https://forum.ih8mud.com/80-series-tech/137411-front-axle-evaulation-faq.html.
and have found no discrepancies.

When turning the wheels from a straight position to the left I can hear a clunk from the front end; and then again when turning back to straiten the wheels.

If the front end is lifted off the ground all is good.

What should I be checking for next?

Cheers,

LandCrusher80






 
Have you checked all of the front end linkage ie. tie rods, knuckle bolts, stabilizer?
Wheel bearing play? Is any of the linkage hitting the lower control arms? Checked for play in trunion bearings?
 
Have you checked all of the front end linkage ie. tie rods, knuckle bolts, stabilizer?
Wheel bearing play? Is any of the linkage hitting the lower control arms? Checked for play in trunion bearings?

My tie rod lock nut backed out bit on my truck and it was causing a thunk when I would turn leaft and right. So check yer nutz!:beer:
 
Check your sway bar mounts on the axle. The right one gets twisted when you turn left. If it's twisted or broken, remove the sway bar until you can get it fixed. Loose sway bar ends have been known to cut ABS and brake lines.:eek:
 
Yes checked them all nothing is loose.
No wheel bearing or trunion paly.
Also the linage looks ok.

Have you checked all of the front end linkage ie. tie rods, knuckle bolts, stabilizer?
Wheel bearing play? Is any of the linkage hitting the lower control arms? Checked for play in trunion bearings?
 
Sway bar is OK.

Check your sway bar mounts on the axle. The right one gets twisted when you turn left. If it's twisted or broken, remove the sway bar until you can get it fixed. Loose sway bar ends have been known to cut ABS and brake lines.:eek:
 
I don't have any experience with this, but thought I would ask.

Front end on jacks.. .OK (correct)
On the ground turning the clunk comes.. (correct)
On the ground is the truck moving? and how fast if so?
 
Something is happening when you take weight off the front and put it back down again are u sure that none of the linkage is not hitting something else? Is it possible that one of your birfs is starting to partially seize or is having issues?
 
While you are at it make sure the radius arm bolts are torqued to about 130ft lbs.
 
You have not said if you have a stock or aftermarket suspension. I installed an old man emu kit and had the same clunk, tried everything I could, read the same fixes and nothing worked. I found that the ubolts that hold the dif to the springs stretch and lose their ability to hold, when you rotated your steering wheel the suspension builds up tension till the spring slips causing the pin that goes thru the spring to clunk into the side of its hole when you turn the other way it repeats. I took each ubolt nut off applied never sieze and reinstalled, I then took a long breaker bar and a pipe extension and tightened the nuts well beyond what seems correct it solved the problem.
I have a 1985 BJ70 not the same as you but it did work for me.
I hope this helps.

Jim
 
What about the track bar? You guys call it a "panhard" bar... My buddy had a clunk issue on his 4Runner a while ago, turned out to be a loose track bar bolt on the rear axle.
 
Correct
Correct
It does it at all speeds.

I don't have any experience with this, but thought I would ask.

Front end on jacks.. .OK (correct)
On the ground turning the clunk comes.. (correct)
On the ground is the truck moving? and how fast if so?
 
Linkage looks good.
Birfs rebuilt 30,000km ago. No wear or tear noted then.

Something is happening when you take weight off the front and put it back down again are u sure that none of the linkage is not hitting something else? Is it possible that one of your birfs is starting to partially seize or is having issues?
 
You should have someone turn the wheels while you are under front of rig to see if you can locate the noise. I am at a lose here with this one.
 
^^ on the front Panhard.

Mine "looked" fine, but was torqued much too little. The frame-side is 180 ft-lb, and the diff-side is 130 ft-lb IIRC...check your manual for the specs for your year model.

Fixed a nasty clunk in my front end, and got me to check all torques in the suspension. 152k miles, and happily quiet now.
 
I also have this issue with mine on J springs...

Not really a clunk though.

I wanna take another look at it this weekend. It's been bugging me. It sounds to me just like when you hear a bolt/nut jumping threads, as weird as that sounds.
 
When turning, in either direction (moving or not moving), it feels like something is binding and then it releases...hence the clunk noise accompanied by significant vibration. All linkages have been checked and the axle was rebuilt two years ago. This issue only surfaced in the past couple of months. If I have someone turn the wheel you can see and hear the clunk but it is not at all obvious where it is coming from.
 
Back
Top Bottom