Front Axle rebuild problem

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 23, 2008
Threads
5
Messages
31
Location
Memphis, TN
I read the FAQ, and FSM, then attempted the front axle rebuild this weekend. Got the parts from Dan, and all seemed to go well until the test drive. Steering much improved. The problem is a noise during low or medium acceleration that sounds like it is coming from the right front wheel area. It does not happen unless I am accelerating, and stops when I let off the gas.

I rebuilt the axle because of leaks and my not being sure when it was last done since I just bought the cruiser.

The birfs were not clicking before and compared to many of the photos that I have seen here were not in bad shape so I packed them and put them back in.

I called myself being careful with the wheel bearing peload and used a fishing sale to set preload to 10-12 lbs on each wheel.

Any ideas where to start troubleshooting?

Thanks
 
The noise is a barking sound, resembles the noise that a seal would make. Sounds like dry metal rubbing or binding on something.
I did put some grease on the spindle bushing prior to putting it back on.
Thanks, for any help you can offer. I hate to start over.
 
The niose is worse during right turns than left, and only during acceleration up to about 20 miles an hour. It is not a steady noise, but a barking repeating noise and stops immediately when I get off the gas.
 
Any ideas?
 
You guys are good!

I went in this afternoon to see what was causing the noise. There was grease on the spindle bushing, but I added more and greased the axle shaft where it goes through the spindle.

Also found what was obviously a heat related problem, and what was probably the cause of the noise. I forgot to bend down the tab on the locking washer and the front bearing had tightened up. Heat related because it was 93 degrees when I did the axle job, this was the last side and I was hot, and obviously careless.

New bearings, torqued right, tab bent down and rollin again. All quiet.

These bearings are a PIA to get set right. My front hubs still get hot after driving, water sizzling hot, and the preload is 6-8 lbs. I'll drive it about 100mi and check again. Have 2 studs from the hub to dtive flange to replace where the PO hulked on the bolts and stripped them. Had to use a nut splitter to get the drive flange off. New studs ordered with spares for next time.

Thanks for the help.:):beer:
 
My front hubs still get hot after driving, water sizzling hot,

If I understand you correctly and you are saying that your front hubs will boil water after driving then you still have a problem. This is not normal.... not even close. Perhaps too hot to hold your hand on it for more than 10 seconds but water should not sizzle if sprayed on your hub.

-B-
 
You understood correctly, after driving 15 miles the front hub and wheel were hot enough that when I sprayed the water hose on them while cleaning the driveway, the water sizzled. I'm gonna check the wheel bearings again when the studs for the drive flange come in and I replace them. I won't bedriving till then anyway. I've read many posts about adjusting teh bearings, but it seems that everytime I torque the lock nut, the adjusting nut tightens enough to change the preload 10 - 15 lbs. Any hints other that keep fooling with it. I have never seen wheel bearings this difficult to adjust.
 
Yeah, the hub turns by hand and the preload on my fighing scale shows to be in the 8 - 10 lb range. The FSM calls for 6 - 12 so I figured that was good. I'm gonna loosen them a little and see what happens. I agree with you that they must be too tight. I may just try it by feel like I used to do on J**ps. It sounds like the J**p is more forgiving though.

Thanks for the advise.
 
I have never seen wheel bearings this difficult to adjust.

Normally, the F&R wheel bearings are not difficult to adjust.

Review the install sequence...

Outside wheel bearing, thrust washer, inner hub nut, star washer, outer hub nut. From memory, torque the inner hub nut to 43 ft/lbs a couple of times to "squeeze" the hub and bearings. Rotate the rotor back and forth several times after you tighten, then torque the inner hub nut to 10 ft/lbs, install the star washer, torque the outer hub nut to 43 ft/lbs, and test to be sure the hub rotates freely. You can check with the scale if that makes you more comfortable. Bend the proper tabs over the inner and outer hub nuts and you're done. This should be pretty close to the Landtank method that I was trying to recall from memory.

-B-
 
Last edited:
Thanks, my problem seems to be the adjusting nut tightening some when I torque the lock nut. I have been tightening the adjusting nut to 5 ft/lbs, because I thought that was about the same as the 48 in/lbs that the FSM calls for. At that point the fish scale is at 6 - 8 lbs. Then I put on the star washer and torque the lock nut to 43 ft/lbs. Checking the fish scale again the preload has gone up, usually to 10 - 12 ft/lbs which should be OK, but makes the hub run hot. I'll have to mess with it more before driving, but have the studs to replace anyway so I'll have the flange off when the parts get here.

Thanks for the advice..
 
If the hub nuts are nicked up then replace them. They are only ~$2 ea. It is possible that you have a stripped one that is not holding the threads when you torque down the outer hub nut. It is normal for the tension to increase a bit when you torque down the outer hub nut.

Experienced mechanics adjust the wheel bearings by feel so if you have done that before then do it the same way. It is not rocket science and the 80 wheel bearings are nothing special though a LOT bigger than your heep bearings.

Sizzling water after a drive is NOT normal. Any chance you have a brake pad dragging? That would heat up the rotor and transfer that heat to the hub.

-B-
 
Thanks Beowulf, I'm gonna give it a shot tomorrow without the fish scale. I think I can torque and release (couldn't help the fishing lingo) to seat the bearings and them put some preload on by feel and lock it down with the lock nut and star washer. I'll see if that cools things down.
 
Back
Top Bottom