Fj80 no ilde

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 3, 2017
Threads
12
Messages
131
Location
Byhalia, MS
Well after i had my MAF rebuilt and drove my fj home it was running smooth as ever.
I put it up on jack stands and am in the process of doing a complete brake job as well as deleting the rusty old ABS system per acticle on this forum and now it will start up but not idle.
The CEL stays on while it starts up but it will only run for a couple of seconds.
I popped open the gas cap and no pressure or vacume there.
Any easy way to check out the fuel pump??
Syggestions??
 
What's the error code? Why are you assuming it's fuel related?
 
Yes. What year? BTW, it's time to invest in a copy of the FSM...
This is from the '94 manual. The later manuals (OBDII) don't have very good descriptions of how the system works; they're oriented toward the Toyota handheld tester. This is the procedure for all 1FZ-FE engines. There are two modes, NORMAL and TEST:

upload_2017-11-28_12-10-20.webp


upload_2017-11-28_12-10-41.webp


upload_2017-11-28_12-11-32.webp


upload_2017-11-28_12-11-53.webp
 
If you have an OBDII model, you can use a generic OBDII wifi-enabled or cabled plug and the appropriate software. The FSM process isn't any better or worse, it's just cheaper.

If you have an OBDI model, you have no choice, you must use this method. Unless you have a Toyota handheld tester, and then I want to talk to you offline.
 
To clear the codes, you can either pull the EFI fuse in the engine compartment (it's marked) for about 30 seconds, or pull the positive lead from the battery. The fuse is the better alternative.
 
Nope. Thats why i was leani g towards fuel. It just starts up and dies about as quickly. I will pull the codes if any and see. Thanks for the help so far..
 
Usually if there’s a fuel delivery issue it’ll have a hard time starting to begin with. The fact that it starts then dies leads me to believe there’s either a massive vacuum leak somewhere or the computer isn’t getting a signal from the MAF or crank/cam position sensors if you have them.
 
Ok, i got it running but it does appear to be a large vacume leak.
Can anyone else listen around their TPS and tell me if they hear air? Im afraid the throttle body may have a leak somewhere. I took it off to clean it and put a new gasket on it but it may be somewhere else.
Anyone know of a place that rebuilds the whole body so it works like its supposed to?
My initial reason to pull it off was idle problems. I still have high/low idle now.
 
The throttle body is two things: a chamber for collecting air, and a bracket for hanging stuff on. There's really nothing to rebuild. Now cleaning it is another story. The exterior isn't going to affect the engine performance but after you finish refolding your roadmaps, it'll make you cringe, if it's not clean. The interior is fairly important and you should clean as much of it as you can. Be careful not to dislodge the carp in there without making provisions for removing it; your valves won't like it at all. If you can spare the time and effort to remove it, clean the whole thing. Invest in a case of carb cleaner, an ultrasonic tank or a small child, with lots of time on its hands. You can clean up the goodies underneath it while you're at it. (hoses, VS valves, that fuel filter you've been ignoring, etc.)
 
The throttle body is two things: a chamber for collecting air, and a bracket for hanging stuff on. There's really nothing to rebuild. Now cleaning it is another story. The exterior isn't going to affect the engine performance but after you finish refolding your roadmaps, it'll make you cringe, if it's not clean. The interior is fairly important and you should clean as much of it as you can. Be careful not to dislodge the carp in there without making provisions for removing it; your valves won't like it at all. If you can spare the time and effort to remove it, clean the whole thing. Invest in a case of carb cleaner, an ultrasonic tank or a small child, with lots of time on its hands. You can clean up the goodies underneath it while you're at it. (hoses, VS valves, that fuel filter you've been ignoring, etc.)
I did exctally that and cleaned the intake (both parts) and put in new injectors since i had it apart.
The vacume leak sounds to be coming from the TPS. Is that possible? Or maybe a line under it. All I know is i hear air right at the sensor and if i push just a little on the throttle assembly while running the idle drops very low. If i throttle it a bit it seems to stick a little and sit at around 800 rpm.
 
Poke around in there with a dentist mirror and see if there's anything obvious like broken plastic.

I've heard that a propane torch (unlit, of course) will expose a leak when the raw gas gets sucked in and raises the idle.
 
If you put in new injectors were they Toyota or aftermarket? Did you seat them into the rail correctly and not tear oring. Did you make sure the electrical plug seated on to the injector. Did you change the position of the tps sensor? What year is your truck? Maf rebuilt? If it's 93 or 94 you don't have a maf, it is a afm or sometimes called vfm, who rebuilt and why?
 
So I read that you pulled your intakes off the engine and apart? Did you replace those gaskets? Or did you just spray bunch carb cleaner down the intakes to be sucked into the engine, if so that will make it run ruff for little bit. When I had a bad afm it ran exactly how you are describing.
 
Try this:
upload_2017-12-1_7-33-12.webp


upload_2017-12-1_7-40-59.webp
 
If you put in new injectors were they Toyota or aftermarket? Did you seat them into the rail correctly and not tear oring. Did you make sure the electrical plug seated on to the injector. Did you change the position of the tps sensor? What year is your truck? Maf rebuilt? If it's 93 or 94 you don't have a maf, it is a afm or sometimes called vfm, who rebuilt and why?
The injectors are rebuilt aftermarket and i learned the hard way how to seat them properly. All gaskets have been replaced, the vain air flow was rebuilt due to not even getting a CEL and a shop told me thats what it needed.
The engine immediately fired up when i had a service on ebay (pullnparts4ya) rebuild it.
It runs smooth and idles fine, just a bit on the high side.
I think i did move the TPS a little when i was cleaning the throttle body. I tried to dissemble what i could toclean it.
 
The injectors are rebuilt aftermarket and i learned the hard way how to seat them properly. All gaskets have been replaced, the vain air flow was rebuilt due to not even getting a CEL and a shop told me thats what it needed.
The engine immediately fired up when i had a service on ebay (pullnparts4ya) rebuild it.
It runs smooth and idles fine, just a bit on the high side.
I think i did move the TPS a little when i was cleaning the throttle body. I tried to dissemble what i could toclean it.
Oh, and its a 94..
 
How high is high? I thought you said it wouldn't hold idle? Did you have the battery unplugged? Did you have the tps unbolted?
 
Ok, i got it running but it does appear to be a large vacume leak.
Can anyone else listen around their TPS and tell me if they hear air? Im afraid the throttle body may have a leak somewhere. I took it off to clean it and put a new gasket on it but it may be somewhere else.
Anyone know of a place that rebuilds the whole body so it works like its supposed to?
My initial reason to pull it off was idle problems. I still have high/low idle now.
Idles around 800. And i hear air/vacume near the TPS. Yes, i had it unbolted a while back. Guess i can try the butane trick to see for vacume leaks.
Other then that the only code it has is the 2nd o2 sensor. I will try to clear codes tonight and warm it up to see if i might need to get a new o2.
Still working on the brakes, just cant wait to drive the beast ya know.
 
Back
Top Bottom