FJ40 - what is this pump for?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 30, 2005
Threads
50
Messages
169
Hi,

While taking the head off my 1982 FJ40, I discovered that there is asecond belt driven pump on the motor. It looks a bit like a power steering pump but actually sits underneath the power steering pump. It has 2 large rubber hose connections which curently do not go anywhere.

Could someone please tell me what this is for and where I should connect it too?


Does anyone have a diagram of all the hundreds of vacuum hose connections and breathers in this setup perhaps? Mine seem to mostly missing or simply looped back onto themselves.


Kind regards
Bernt
 
Smog pump.

I'd be lying if I said I knew exactly what it's purpose is/was. Something to the effect of pumping exhaust gases back into the combustion cylinders when needed to reduce emissions.
 
I think that would be the air pump....the smog pump.:)
 
Holy Moly, no wonder I couln't puzzle it out!!

Thanks for the diagram.

Im not too sure it is is exactly right for my FJ40 as I do not have a computer - I think and hope? (scratch head)

Where would/should this computer box be located?
I am now curious and I am on my way to lift the bonnet to investigate :-)


Regards
Bernt
 
well who knows how much smog stuff there is down there. Here an 80 had a tons of spagetti. you might only have half of it like the earlyier ~76 ish cruiser
 
The air pump takes air from the air cleaner and pumps it into the exhaust stream in the head. It was intended to oxygenate and cause futher combustion of unburned fuel and carbon dioxide in the exhaust. The truck originally had an air injection manifold in the head. You will probably find plugs in the existing air injection holes in the head.

I don't know about an 82, but earlier models had the smog control computer on the firewall under the dash on the driver side. The computer ran all of the smog gear, including the air injection system.
 
Thanks for that.

I do have some hydraulic style fittings with nuts on the end that look like there is a ball inside them, blocking them off. These protrude from the head, above each exhaust port.

I also have a large pipe stub with nothing on it on the airfilter housing. This seems to match the fitting on that obscure pump and maybe that is where it used to go.


This is all very interesting and I wonder if it needs to be repaired or simply left alone. It was obviously removed for a reason at some stage.


I looked under the dash above the accelrator pedal (we are right hand drive). The fuse panel is there and behind it, I found 2 connectors with 3 or 4 terminals each. Maybe that was for the computer at some stage?

Oh boy...


Regards
Bernt
 
The fittings that you mention protruding from the head sound like the remnants of the air injection rail. Usually, these are plugged with 1/4" NPT plugs (the threads in the head are actually metric, of course, but the 1/4" plugs do the job).

Your smog computer may be on the right side or may be on the left under the dash. I really don't know. If it's there, leave it. There's no need to remove the electrical portions of the smog system.

The stub on the front of the air cleaner was the intake for the air pump. It should be plugged.

Your air injection system is disabled and there is no reason to repair it, unless you have smog inspections that require all OEM systems intact. Does the pump have a belt? The pump can seize up and cause failure of the belt, so some people gut the pump and some people replace it with an idler pulley. On some models, the pump is on it's own belt, so the belt is just removed to disable the pump.

HTH.
Todd Bull.

berntd said:
Thanks for that.

I do have some hydraulic style fittings with nuts on the end that look like there is a ball inside them, blocking them off. These protrude from the head, above each exhaust port.

I also have a large pipe stub with nothing on it on the airfilter housing. This seems to match the fitting on that obscure pump and maybe that is where it used to go.


This is all very interesting and I wonder if it needs to be repaired or simply left alone. It was obviously removed for a reason at some stage.


I looked under the dash above the accelrator pedal (we are right hand drive). The fuse panel is there and behind it, I found 2 connectors with 3 or 4 terminals each. Maybe that was for the computer at some stage?

Oh boy...


Regards
Bernt
 
Hi all,

Thank you very much the ifo. I am educating myself on the smog system :-)

My pump is not seized and still has the belt on it. That same belt also drives the waterpump and alternator - I think.

I will plug the stub on the aircleaner once I have it all back together again.
The pump in and out are shorted with a piece of hose so that should be ok.

Question is, how did the pump outlet (large pipe) conect to the 6 injectors on the head? Was there another box which had 6 outputs or something and where was that located?

I have no plans of conenccting it all up but I must know how it all worked and fitted together :-)

Where can I read mor about this system andits operation?

Kind regards
Bernt
 
The air injection manifold ran the length of the head. Those 6 stubs you have remaining in your head all connected directly to the manifold. On the front end of the manifold there was a check valve which prevented back-flow of exhaust to the pump. The pump outlet hose connected to the check-valve.

The manifold is piece #20 shown on the 75-79 Emissions diagram on this SOR page:

http://www.sor.com/sor/cat048b.tam?xax=7306
 
Back
Top Bottom