FJ40 advice on 5.3 vortec swap

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 29, 2010
Threads
4
Messages
19
Location
Perryville MO
Hi everybody new to the web site. A little info on myself and my fj40. Got it when i was 15 drove and worked on it tell college. The original f2 died on me and i am putting a 5.3 with the marks bell housing adapter. I am also going to put the 2.5 MFA lift. So my 33 10.5 wont hit the wheel wells any more. I would like to put a limited diff in but i don't now witch one to use. Any one that has done a swap like this or a lift i would love a little advice on it all. Thank You Danny

n516972752_46996_7464.jpg
 
have you looked through the Tech Links at the top of the page it has a lot of the info you are after IH8MUD.com - Technical and you might want to look in the FAQ section too https://forum.ih8mud.com/40-55-seri...-asked-questions-f-q-updated-28-jul-09-a.html and this isnt the 5.3 but it has some info Vortec Conversion and i wouldnt bother with a limited slip diff just go Aussie locker you should find that info in the FAQ or maybe tech section and don't forget to try the search function at the top of the page. and you will find lift info in there too, i went with 2 1/2 lift from skyjacker http://www.skyjacker.com/ but man-a-fre makes a good product. try searching for all this stuff while you wait for others to chime in on it and good luck!
 
Hi All:

I have a buddy who is swapping a GM 5.3L V-8 into his already SBC powered 40 Series. It is a lot of work to sort out all that wiring!! :eek:

You are better off finding a good, used 2F and slapping that into your FJ40.

For a LSD in the rear axle I'd go with a Detroit TrueTrac, which uses gears, not clutch packs.

Regards,

Alan
 
I did a 5.3 in mine and a 4" MAF OME lift with the shackle swap. What are you looking to know? Check out the FAQ and tech pages, but if you still have questions, let me know.:cheers:
 
hi guys
Thank u for the info so for. i am just starting on this project. i went through all the lift and there was just so many different opinions i was looking for some one who has done that lift with the same size tires. The 5.3 i really want to do i got the motor cheap with only 30,000 miles on it. i have no experience on rear ends so any more advice on that would be great. thanks
 
Kirn, PM me for some info you are going to need regarding a 40 pulse reluctor ring signal your 5.3 will require. Only one choice when using a Toyota 4 speed tranny and transfer-case.
 
I am starting a 5.3L installing into a 1963 fj40. it is a lot of work and alot of parts are starting so add up. the wiring wont be that had. i have done other fuel injection swaps before. untill the end of march painless wiring harness is offering $100 rebate on the harness and free computer programming. the original harness price is $595. i have shopped around and unless you already have a harness that can be modified, painless is the cheapest. check out my build " a new home for snotz"
 
I did a 350 tbi with marks adapter and a 2.5" lift with a pto winch. Marks adapter was great. You will have to watch the radiator clearance. I barely had room for a taurus fan and a al. radiator. I move the Radiator as far forward as possible. I dont know how far the 5.3 pulleys stick out.
 
Hey Downey i am new to the hole forum thing what does PM mean? Thanks for the help
That means send me a private message. Better yet, just give me your mailing address (street address) and I'll send you a freebie V8 instruction manual. Unfortunately I don't have it set up on PDF yet for e-mailing. Your 5.3 with stock 4 spd. tranny and transfer will require a 40 tooth reluctor ring kit on the back side of the transfer-case. If this sounds confusing, you can call my cell (562) 360-9470.
Jim Sickles
 
Wow, I know this is a really old thread but I am just beginning a 5.3 LS swap and the subject of a VSS has never occurred to me. Can anyone shed some light on this and what works best when using the stock transmission and transfer case? 1978 FJ 4 speed. Thanks in advance.
 
I don't know if anybody is making anything suitable at the moment. Perhaps Dakota Digital has something that can be used. I made my own to bolt to the rear input shaft cover on the transfer case.

It's covered in this thread: V8 conversation help
 
1. See if Stealth Conversions still makes the reluctor ring kit for the back side of the transfer-case.
2. If they don't, then you may have to use a Dakota digital $$$ dash gauge kit to get the 40 pulse signal the 5.3 will be looking for.
 
I used a 40-tooth ABS brake reluctor (from a Chevy, I believe), had it bored out slightly to just fit the input shaft and then sandwiched it in the spacer stack behind the rear bearing. I made the housing to replace the rear cover and mounted a stock mag pickup in it. It works.

A friend of mine did something similar and modified the speedo housing to mount the mag pickup and fit a reluctor to the output shaft.
 
Back
Top Bottom