Finally - J Springs!!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 30, 2006
Threads
103
Messages
3,952
Location
Utah
After months of looking and waiting and looking again, I finally came across a sweet deal on front J springs. LandCruiserPhil was selling his for $135 shipped, so I jumped on it. They came to my door a day early, which I thought was cool, and were on my truck within the hour. :D

Before the J's, I was using Ironman 2" coils in the front and 860's in the rear with 30mm MAF spacers all around.


Here are some pics:

Before, Ironman 2" fronts w/spacer
4913_220906615227_539070227_7430857_7338886_n.jpg


After, 850J fronts w/spacer
7935_275970585227_539070227_8775030_6857072_n.jpg


And for kicks and giggles, this is before I did ANYTHING
n539070227_6079969_4931877.jpg


Measurements

Ground to fender:
RF- 40"
RR- 39.25"
LF- 39"
LR- 38.75"

Center-of-hub-to-fender:
RF - 25"
RR - 24"
LF - 24.5
LR - 24"

I think I have around 4" of lift....Does anyone have measurements I can compare to?

I'm thinking of upgrading the rear springs to 863's, 863J's, or possibly 864's (I like a bit of load-carrying capability) so I can get rid of the rear spacer... Can't decide. Oh well.

More pics to come whenever they decide to start cooperating... :doh:
 
Last edited:
looks good, now give me your old springs. lol.
 
uh oh those 33's are looking small....

I'm about to do J's as well, but not looking forward to the expense of bigger tires.
 
Last edited:
alot more follks will have ctr of hub measurements for comparisons sake.... heres a few #s

Looks good!! now w/ the spacer on top of J's are you getting any vibes? or have you adjusted castor yet?

https://forum.ih8mud.com/80-series-tech/95899-diffrent-rigs-diffrent-setups-measurements.html

(ok just read those measurements arent ctr of hub either, and the second rig is on J's w/ 285's instead)

Yeah I'm getting vibes around 60-70 MPH, but I know for sure one of my u-joints is going bad. I was getting vibes before the J's.

BTW, no castor correction. At all. :o
 
It now looks leveled. Nice stance. But J springs suck. Enjoy them while they are young. After 60K or less miles of moderate wheeling and/or road driving they will be like slinky. You'll know :cheers:
 
It now looks leveled. Nice stance. But J springs suck. Enjoy them while they are young. After 60K or less miles of moderate wheeling and/or road driving they will be like slinky. You'll know :cheers:

How much of that is the spring, and how much of that is the relatively soft OME shocks?
 
How much of that is the spring, and how much of that is the relatively soft OME shocks?

I'm running original Toyota shocks. 262k on them and still decent :lol:

Now, does anyone have stock center-of-hub-to-fender measurements?
 
I'm running original Toyota shocks. 262k on them and still decent :lol:

I actually like the OEM shocks.

Have you done anything to space them down to increase travel? Or are you just accepting limited flex?


Now, does anyone have stock center-of-hub-to-fender measurements?

I'll try and remember to get this for you tonight....
 
I actually like the OEM shocks.

So do I.

Ebag333 said:
Have you done anything to space them down to increase travel? Or are you just accepting limited flex?

:p Is there a way to space down the shocks?

I just found this from a couple years ago...

l_7966bc3e54cce3a4f556cce7d941f9c5.jpg
 
:p Is there a way to space down the shocks?

Sure, lots of ways.

One I saw was simply taking some box steel, drilling a hole through it. Bolt the top hole to the existing mount, bolt the bottom hole to the shock. That spaces you down quite a bit (depending on how big a piece of box you use).

You can do the same for the bottom mount on the front.

I also saw one that basically took some threaded tubing, and had a stud/bolt welded to it. The threaded tubing went on the shock post, threaded stud bolted up as normal. Would be easy to get exactly how long you wanted with that. Just be sure you loctite it if you go that route (the threaded tubing can spin loose).

Either one would be super easy to make. Just be sure you measure your compression so that you know how far to space it down, you don't want to overcompress your shock.
 
Back
Top Bottom