F engine distributor

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 12, 2005
Threads
24
Messages
234
Location
Prince George, BC
I have a 74 FJ40. It has been giving me trouble with burning out breaker points regularly with a new condenser installed every time I replace the points (worn bushings in distributor?). I think it's a vacuum retard distributor , so I want to replace it with a vacuum advance distributor. What years of crusers came with these?
 
Best bet is to grab a distributor from a 78 or later 2F. Fully electronic, and waterproof. After 80 I believe they also switched to a ball-bearing instead of bushing. You'll also need the side cover (unless its a 78 or 79), and the coil/ignitor.

The non-USA vacuum advance is the same as the pre-68 distributor, and this is also a common swap. I think a 77? might also be vacuum advance. I've got one, but I'm not sure which year its from, so there may be others...

Matt
 
If you are running a coil that produves more voltage then stock you will need a ballast resistor so that the points dont get burnt. I always replace my stock ign coils with MSD Blaster 2's and the ballast. In my last FJ55 I used a non-us distributor and non-us carb.

or you can pull everything out and spend the extra cash for an HEI conversion distributor and call it a day.
 
The points are regularly destroyed if/when you leave the ignition 'on' without the motor running. No matter what you do with the coil/dizzy/resistor, you need to either quit leaving the ignition on or install an ignition cutoff switch so that you can turn the key on without powering the coil.

All that said, you can solve your points worries forever by installing a pertronix ignitor setup. $60 well-spent - and I'm a cheap bastard.
 
its an electronic ignition that replaces the points. Very easy to install. We have been using them for years on aircooled VW's. JT Outfitters sales the same thing rebadged. Its the Pertronix with a different name. So it doesnt matter where you go because it is made by Pertronix and not JTO's buddy jack or what ever his name is.
 
nate said:
What exactly is the pertronix ignitor??

A magnetically-actuated ignitor setup. There's a magnetic reluctor collar that goes over the distributor shaft, and the pickup senses the rotation of the shaft. No more contact points to wear out, and you never have to set the dwell since it's pre-defined and not changeable.

Pertronix website

Catalog page (pdf)

edit: look at the top menu bar. There is a little button labeled 'search'. Try it. Use it. Love it. :flipoff2:
 
I don't leave the ignition on without the engine running so I don't think that is the problem. I am interested in the pertronix setup. So a rotor just slips over the breaker cam and replaces the points with a stator? What else do you have to do to install this?
 
landcruiserrich said:
I don't leave the ignition on without the engine running so I don't think that is the problem. I am interested in the pertronix setup. So a rotor just slips over the breaker cam and replaces the points with a stator? What else do you have to do to install this?

Take out the condensor, and run the wires to the coil. Literally, that's about it. Set it and forget it.
 
nate said:
Do you know if it would work as a band aid to a dizzy that's got loose bushings?? I think I might get on of those ignitions.

I think 'band-aid' is a good term. Yes, it will help since the dwell will be consistent. Your idle will smooth out and setting the timing will be a bit less of a guessing game.

In the long run, I would still look into getting the dizzy replaced or repaired (I've never done the bushings before - can't be that hard?). Either way, it's not that expensive to get a good used one.
 
What is the difference between USA and non-USA for the dizzy? I can get a decent used one off a 74 for $45 plus shipping, that a decent deal? I have 2 already, both have worn bushings.

Anyone know how the shaft would come out to get to the bushings? I wasn't able to figure that out.

At this point, I'm just turning the 40 into a decent driver, so it's on a buject. I have a Jeep with is my no budject money pit :)
 
On a budget? Then don't F around with the dizzy. You'll end up needing a new engine if you're not careful. Ask Romer, one of our resident experts.

If you can't afford a new engine, then consider all the money you'll be saving by just buying a good distributor the first time.

Another thought on your points issue. If you're running a generic aftermarket ballast resistor, it may be that the resistance is not sufficient to keep from burning the points. In that case, you would need a Toyota unit. I had this problem with my first truck 19 years ago, and only the Toyota ballast cured it.
 
A '75 distributor is not one of the more desirable ones. People tend to go with
the pre-68 nor non-USA which is almost the same thing or the later > 79. I
wonder if there's any specs for allowable runout in a dissy. I have 5 used ones
and don't know how much play is too much. I also don't know who to get
lube down to those bushings.
 
nate said:
So where is the balast resistor everyone talks about? and can I test it??

The ballast resistor should be in line with the positive wire to the coil. It's a large ceramic block with a terminal at either end. Testing requires a FSM for correct voltage.
 
To respond to nate's question about the difference between non-USA/USA dizzy. the non-USA dizzy is a vacuum advance distributor with adjustable advance/retard and it has points in it. it's basically a brand new pre 68 distributor. The distributor in the 74 is a vacuum retard unit that doesn't do it's job all that well once you scrap all of the emissions control junk hanging all over the engine. It has massive mechanical advance weights in it and the vacuum diaphragm just keeps them from advancing the timing too far. a bad setup because vacuum advance is needed at low rpms for power.
 
Back
Top Bottom