electrical mystery

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 2, 2006
Threads
13
Messages
35
Location
bozeman, montana
here is what ive got going on with my 78 40. ive got to jump it to get it going....let it run for twenty minutes....turn it off and immideatly try to start it and nothing, no click, no turn over, no anything. the battery is not charging at all. throw the jumper cables back on and it will fire right up.. so far i have replaced the battery and cables, pulled the starter and had it checked out, cleaned up the connections to the starter, pulled the alternator and had it checked out...today i am going to clean up the connections from the alternator but i dont think that is the problem because once i get it going it will run all day, until i turn it off, then nothing. any ideas where my fault lies...why is my battery not charging at all?
thanks!
matt:cheers:
 
alternator passed.....when running, the amp meter sits where it used to when it was running right, justbelow the middle of the gauge, when i try to start it, when it is dead, it jumps to about the middle of the gauge
 
alternator passed.....when running, the amp meter sits where it used to when it was running right, justbelow the middle of the gauge, when i try to start it, when it is dead, it jumps to about the middle of the gauge

I wouldn't think below the middle would not be good. That means that the altanator is not keeping up with the load and the battery is being used. At that time it is not charging

Mine starts off charging and is far to the right(above), after the battery is charged it drops down to just barely right of the middle.

How long have you had this cruiser? Batterys have a long running time without being charged on a FJ40 cause a lack of alot of electronics.
 
ive had this cruiser since march and it is my first. i started having this problem when i moved from colorado to montana...every time i stopped for gas my girlfriend had to jump me....what pain in the ass huh:) . which is funny to me though because i could drive a full tank of gas no problem. also with the amp meter, that was an estimate and i wish i could go outside and check it to be sure but i have to walk 20 minutes to library to use the computer. i just dont understand why the alternator keeps the truck running but my battery is not getting a charge...could this possibly be something in my ignition system? the alternator checked out at 14.something amps
thanks :cheers:
 
My guess is you have enough power on your battery to run your cruiser not start your cruiser. I'm still thinking alternator because your amp meter.

If you had a multimeter you could check your battery with it off and it should be around 12VDC normal. Check it running should be like your saying 14 volts dc. If your getting 14volts then your battery is no good if it is not charging.
 
Last edited:
You've covered a lot of bases already. You should also measure the voltage across the battery terminals with the engine running. Even though the alternator bench tested fine, it's possible it isn't wired to the truck correctly. You should get 14.something (volts).

Another possibility. I had no-start symptoms like you. (Stuck in Rittsville until a couple of cowboys gave me a push start.) I replaced the ignition switch and fixed it. Not the lock and key, but the plug-in unit behind it, in the column. 15 bucks from Kurt at CruiserOutfitters.
 
the battery seems so flat dead that it wont even make the idle solenoid on the carb click...no click, no turn over, pretty dead...do you suggest it is the alternator then?
by the way i really appreciate your imput, i understand it is difficult and sometime frusterating to diagnose a problem with out seeing it and your opinion is greatly appreciated!:cheers:
matt
 
No problem. Any cheap voltmeter will work. You should have one anyway eventually if you want to troubleshoot electrical stuff. Borrow one if you have to.

Just put the dial to DC Volts and hold one lead on each battery terminal. Meter will tell you battery voltage. Running and charging the voltage should be 14.something. Engine off and charged it should be 12.something. Engine off and dead battery it will be below 10.something.
 
also, i like the ignition switch idea, but why when i jump it does it start right up?

Mine did that a few times. I had a spare battery in the back and jumper cables. Worked a few times, then I couldn't get it to go even with a jump. Hungover cowboys to the resue. Drove the rest of the way home without shutting it off.

I need to add that I rejuvenated the solenoid contacts at the same time as I replaced the ignition. It's possible that is your problem. Again, starter bench test is with full power source and no switches or wiring. Could be that is enough juice to overcome "marginal" solenoid contacts. Also, Toyota solenoids are known for this and are pretty easy to fix.
 
also i noticed there are 2 'B' leads coming off of my alternator, one is really corroded and the other looks new and clean, are these interchangeable (can i connect the wire that was on the corroded 'B' lead to the clean one?)
 
Have you tried charging the battery? If it (the batt) will hold a charge AND start without jumping it you have eliminated a lot of possibilities...I would have the alternator looked at again if the above works. HTH
 
It's no fix , but until you get this sorted out, a jumper battery
pack would not be a bad addition. I keep one in my truck
"just in case" and I really don't like jumping other's trucks with
my truck's batteries. It's also handy for a lot of other purposes as well
as making jumping of others a breeze. No moving trucks around to get close
enough to jump etc, which can sometimes be hard to do on a trail.
After a "jump off" I just plug it in to the lighter socket and recharge the pack
while driving.
As for your problem my money is on the alt. Bad or wired up wrong.
Good luck.
 
Back
Top Bottom