Electrical Diagram ??

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Brentbba

Former Golfer
SILVER Star
Joined
Mar 27, 2003
Threads
449
Messages
11,094
Location
OC, CA
Need to hook up a final wire for my Surepower to a hot lead for the Starter/Ignition. IPOR does not have the diagrams for a 94.

Anyone with the Electrical Wiring FSM for a 94 tell me the location and wire color for the hot lead?

I know I could run right down to the starter and pick up the #50 bundle there, but is their an easier place under the DS dash?

TIA

Brent
 
This was posted by another forum member. Sorry don't remember where or who. But believe this was behind the DS kick panel.

The 96 has an open plug with 12v iignition behind the radio.
12v_source.webp
 
... but is their an easier place under the DS dash?

Brent,
When I want switched +12v at the DS dash, I pull the cover off of the fuse panel to the left of the steering column, remove the screws holding in the fuse panel, and choose one of those wires. (See the EWD and the fuse panel to pick an appropriate slot.

-B-
 
Brent,
When I want switched +12v at the DS dash, I pull the cover off of the fuse panel to the left of the steering column, remove the screws holding in the fuse panel, and choose one of those wires. (See the EWD and the fuse panel to pick an appropriate slot.

-B-

Good source. If you're pulling it from the fused side of these wires, make sure you don't pull too much juice or you'll be popping fuses. Either way make sure your lead is fused also.
 
I believe the wire you want is the "start" wire. This wire allows the surepower to connect the batteries if the main battery is dead for emergency start situations.

Remember that if the secondary battery is dead, it will effectivly drop the voltage when you try to start the vehicle. I would consider putting a switch in line on the start wire. In either case fuse the wire right at the source of the tap.

I would tap it at the first connector coming off of the key tumbler behind the driver side underdash. These are usually nice big pins that are easily removed and reinstalled on the connector. Just remove the pin and solder a fuse holder onto the crimped part of the connector so it doesn't affect the ability to reinstall the pin. If you don't feel comfortable with this procedure you could consider a "t-tap" type connector. This type of connector is usually frowned upon but if done correctly will perform fine as well as be as non invasive as possible.

Lastly, the wire you're looking for should be blk/wht in a readily accessable connector as mentioned before. I believe it is usually an 8 pin connector based on past experiences with Toyotas.

Good luck
 
You are correct - Surepower wants the start wire.

I believe the wire you want is the "start" wire. This wire allows the surepower to connect the batteries if the main battery is dead for emergency start situations.

Remember that if the secondary battery is dead, it will effectivly drop the voltage when you try to start the vehicle. I would consider putting a switch in line on the start wire. In either case fuse the wire right at the source of the tap.

I would tap it at the first connector coming off of the key tumbler behind the driver side underdash. These are usually nice big pins that are easily removed and reinstalled on the connector. Just remove the pin and solder a fuse holder onto the crimped part of the connector so it doesn't affect the ability to reinstall the pin. If you don't feel comfortable with this procedure you could consider a "t-tap" type connector. This type of connector is usually frowned upon but if done correctly will perform fine as well as be as non invasive as possible.

Lastly, the wire you're looking for should be blk/wht in a readily accessable connector as mentioned before. I believe it is usually an 8 pin connector based on past experiences with Toyotas.

Good luck
 
If you wanted to take the easy way out, you could just wire up a switch to provide 12V to that input whenever you choose. This is how I will eventually wire mine when I do my dual battery setup. The only time you will ever need this connection is when you need to "jump yourself" if you accidently kill your main battery.
 
If you wanted to take the easy way out, you could just wire up a switch to provide 12V to that input whenever you choose. This is how I will eventually wire mine when I do my dual battery setup. The only time you will ever need this connection is when you need to "jump yourself" if you accidently kill your main battery.

That is an option in the wiring diagram provided from Surepower. Only advantage to wiring to the 'start' is that the Surepower will then perform the autojump automatically instead of using the manual override switch.
 
Back
Top Bottom