ECU Units

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 13, 2005
Threads
204
Messages
1,820
Location
Boise ID
Thinking my ECU is going bad I have read that there are two types of ECUs for hte 1fz-fe. One was for the 93 and 94 and another for the newer models.

I have a 93 with a new 1fz-fe but dont know what year it was from and was wondering that I might have these crossed and that is causing the bad stumble every once in a while.

Is there an actually two different ECUs for the 1fz-fe and how can I tell to match the right one up with my engine?
 
What is the part number on the tag of the current computer?
 
If you need an ecu for a 93, I have one. A year or so ago I had a miss that could not be diagnosed and I was advised to get another ECU( i think Toyota calls it the PCU--power control unit). My wrench found a rebuilt one we installed it and the problem was not fixed. I put the original back in the car and the replacement is still in my garage. If you need one, I will gladly cut you a good deal.
 
took a while to respond with work and then I was over in Idaho for a while.

Put in a new TPS sensor and code 41 is still on then looked at the computer and mine was built in 5/93 and the last digits werent what firedog said. Mine are 60170. Is this for the later models? There is a new engine in there and I dont know what year that was from.
 
Is there an actually two different ECUs for the 1fz-fe and how can I tell to match the right one up with my engine?

Dan can tell you if you have an updated ECM for your model.

There were several ECM of the US Spec 1FZ-FE engines; not 2. I think there was a different ECM for every year. Possibly 96 & 97 are the same but Toyota listed "improved fuel mapping" as a model year change for 1997.

-B-
 
There is a new engine in there and I dont know what year that was from.

You need to find out what year your engine came out of. There was a significant change in fuel management between 1994 and 1995. The 1995-97 models use a MAF system; the 1993-94 use the AFM system. You will have other sensor differences too so finding out what year your engine is will be important in getting the correct parts.

-B-
 
Looks like youare correct. I just need to find out what year the engine is and then try and match computers. Would the rest of the electrical go haywire or does the ECU strictly run the engine?
 
The ECU as you refer to it is known as the ECM (Engine Control Module) in the EWD. It primarily controls the engine but it gets inputs from sensors all over the vehicle and it controls outputs all over the vehicle; O2 sensors, AT temp, coolant temp, dash lights, etc.

I believe you could take a 1997 engine with a 1997 ECM and all the '97 sensors, and shove it into a 1993 vehicle. I am not aware of anyone that has done that but it looks to be possible.

Post pics of your engine and get the engine number from the plate on the right side of the engine. Maybe we can help you figure this out.

-B-
 
I believe you could take a 1997 engine with a 1997 ECM and all the '97 sensors, and shove it into a 1993 vehicle. I am not aware of anyone that has done that but it looks to be possible.


-B-

You would have to use the wiring harness from the '97 as well, and i don't think you would ever get everything to work right (OBDI vs OBDII needing to know what everything else is doing)
Sounds to me like your Cruiser must have a '94 engine in it (if they put in a "newer" engine. That way the '93 harness and computer would work without issue.
One thing is certain, if the truck has been working with the computer from the '93, then either the '93 or the '94 computer will work, but the '94 is preferred.
 
You would have to use the wiring harness from the '97 as well,

Probably would need the '97 the transmission and transfer too.
-B-
 
The only difference between a 93-94 and a 95-97 motor is the addition of a crank position sensor in the oil pan and a different throttle body. The basic long block can be used in either truck. The only issue would be trying to use a 93-94 motor in a 95-97 truck with the 93-94 oil pan, lower timing components and no crank position sensor.
 
I doubt the ECM is causing your stumble. My 93 threw the 41, 81, 82, & 83 codes and never ran poorly, I replaced the ECM with a used 60221 from a wrecking yard and the 81-83 codes went away but not the 41 code. I then replaced the TPS, but it took some fine tuning of it's adjustment per the manual to eliminate the 41 code (Read lots of dinking around and then swearing a month later when the light came back on). I never could adjust it right while it was on the truck, finally wound up removing the throttle body and adjusting it while on the work bench.

A stumble is more likely to be a damged wire in the harness somewhere, most likely near the EGR valve, or a cracked intake tube. Rule out these before dumping coin into your ECM.
 
I doubt the ECM is causing your stumble.

I agree with Bear. We got off on a tangent answering your questions about the ECM part numbers but skipped over your basic problem.

Bear gave good advice on how to isolate the stumble. Start simple with a good tune-up and go from there.

-B-
 
The only difference between a 93-94 and a 95-97 motor is the addition of a crank position sensor in the oil pan and a different throttle body. The basic long block can be used in either truck. The only issue would be trying to use a 93-94 motor in a 95-97 truck with the 93-94 oil pan, lower timing components and no crank position sensor.

One more difference: the 93-94 uses a vane air flow (VAF) sensor for the air intake, while the 95-97 uses a mass air flow (MAF). They are not compatible, and hence the ECU must match the type of sensor used.
 
It doesnt act up that much or on a consistent basis to probably be the computer. I have already checked all of those my next step is to take the throttle body off and try and set the TPS jsut right. I just have a chiltons manual and they set it by checking the resistance at differnet feeler guage thickness of the throttle.

Is following these resistance numbers the best way to set it?
 
I would check the ignition wires. When were they last changed? Check their resistance and report back. With any diagnosis the best bet is to rule out the simple stuff first. You will save big $$$ in the long run.
 
Back
Top Bottom