Easy mods gone bad....

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 7, 2006
Threads
12
Messages
75
Yesterday, I tried retensioning my seat belt retractor. I was getting tired of shutting the door on the belt and the mod looked so easy in "Minute Mod" :)http://www.4x4wire.com/toyota/minutemods/seatbelt/ The spring went zing and the tang untanged itself. New belt is on order.

Today I tackled the CDL switch install. A search of the archives revealed that it should be easy (quote) "It took me five minutes including the time to admire my work." In my case the PO had glued the "cubby" back into the dash after breaking one of the retainer clips. I broke it out with a hammer and screwdriver (tool abuse?) to get to the hidden screws. Now, I need the cupholder to cover up the hole.

Tomorrow I look forward to screwing up the pin 7 mod. Don't even try to tell me how easy it's going to be!!!! Jinxed ;) Paul
 
Thats too funny .... but only because I can relate all too well. ;)



Peace,



TY
 
Sorry, long.

Well, I tackled the pin-7 mod today. This time, I was expecting the worst and hoping for the best. I knew it was going to be painful because of the location of the mod down by the kick panel, so I took two Excedrin before beginning. I don’t contort as well as I used to and have put on a few pounds (270) since the days when I last worked on cars.

How Slee found room to take a picture of two hands working on that connector, I’ll never know. I was able to get my head, shoulder and one hand inside the door, or both hands but no eyes. The flashlight had to be balanced on the brake pedal.

My first challenge was the four screws mounting the ABS computer to the bracket – they wouldn’t budge (even with a brand-new Craftsman screwdriver and a squirt of PB Blaster). So … I unbolted the bracket, instead, losing my 10 mm socket behind the panel. I was finally successful in getting the connector unplugged (remember, this is either using only one hand or working with two hands, but blind). Identifying the wire colors required cutting away some of the sheath on the wiring harness. I held my breath with each nip of the side cutters on that plastic sheath until an inch or two was removed. So far, so good. Getting the pin out of the connector was troublesome, though -- not having the "terminal pick" pictured in Slee's instructions, I tried a dental pick and, then, a tiny screwdriver without success. So, I decided to cut the wire instead.

I put it all back together and tried it out. CDL light is still on when in 4-low. :eek: So, I go inside to look at the instructions again. Yep, I cut the wrong wire. I wonder what the black wire with red tracer does?

Needless to say, Raven’s water temp gauge mod just got dropped off my list!!

Paul
 
Well, I tackled the pin-7 mod today. This time, I was expecting the worst and hoping for the best. I knew it was going to be painful because of the location of the mod down by the kick panel, so I took two Excedrin before beginning. I don’t contort as well as I used to and have put on a few pounds (270) since the days when I last worked on cars.

How Slee found room to take a picture of two hands working on that connector, I’ll never know. I was able to get my head, shoulder and one hand inside the door, or both hands but no eyes. The flashlight had to be balanced on the brake pedal.

My first challenge was the four screws mounting the ABS computer to the bracket – they wouldn’t budge (even with a brand-new Craftsman screwdriver and a squirt of PB Blaster). So … I unbolted the bracket, instead, losing my 10 mm socket behind the panel. I was finally successful in getting the connector unplugged (remember, this is either using only one hand or working with two hands, but blind). Identifying the wire colors required cutting away some of the sheath on the wiring harness. I held my breath with each nip of the side cutters on that plastic sheath until an inch or two was removed. So far, so good. Getting the pin out of the connector was troublesome, though -- not having the "terminal pick" pictured in Slee's instructions, I tried a dental pick and, then, a tiny screwdriver without success. So, I decided to cut the wire instead.

I put it all back together and tried it out. CDL light is still on when in 4-low. :eek: So, I go inside to look at the instructions again. Yep, I cut the wrong wire. I wonder what the black wire with red tracer does?

Needless to say, Raven’s water temp gauge mod just got dropped off my list!!

Paul

:doh: Sorry to hear....

This is the exact reason why I try to stay away from any electrical mods. :)
 
I was changing out a froze up alternator idler pulley & managed to bust off that damn little nipple on the top of the radiator




I had lots of other things I could have spent that $400+ on instead of a new radiator.....
 
I don’t contort as well as I used to and have put on a few pounds (270) since the days when I last worked on cars. ... Yep, I cut the wrong wire. I wonder what the black wire with red tracer does?

For big guys, sometimes we need to make a little more room. Removing a front seat is easy (I know, I know...) 4 bolts and the connector to the power seat assembly.

How Slee found room to take a picture of two hands working on that connector, I’ll never know.

I believe those are Dan's pics. Dan is a little smaller than Christo (and me!). :D

Yep, I cut the wrong wire. I wonder what the black wire with red tracer does?

Are you color blind? :D :D :D

-B-
 
I was changing out a froze up alternator idler pulley & managed to bust off that damn little nipple on the top of the radiator




I had lots of other things I could have spent that $400+ on instead of a new radiator.....

why don't you just braze the nipple back on ?
 


Needless to say, Raven’s water temp gauge mod just got dropped off my list!!

Paul


It's a shame that we won't get to see the third installment of this trilogy series.
:lol:





Paul,

You don't have your location posted, but maybe there's someone in your area that has done the temp mod and can help you out?

Just a thought :cheers:
 
I think we all have spent an entire Sunday on that "small" thing we told our wives we'd be done with before lunch.
 
Not me...........



One late afternoon I was out working on my in-frame receiver and my wife came out and asked me "When will you be finished?"

I said "about 15-20 minutes." (foolishly thinking that she was referring to an impending meal....:doh: )


She replied "No, with the truck"

:o :o :o
 
Thanks, -B- , for the seat suggestion --

My friends are in similar shape re squeezing into tight places, so I didn't really have a recovery plan. Besides, I'm going to have to start doing my own work for financial reasons. After reading your suggestion, I was out the door to pull the driver seat when it started to sprinkle. Great! Now I get to obsess over the four bolts. (Can't wait to do the Birfs ;)

And yes, I am color blind (The red traffic light is the one on top), although the problem with cutting the wrong wire was a small case of attention deficit disorder. I miscounted the wires in the picture of the instructions and I meant to cut the next-to-last wire on that plug.
 
Not me...........



One late afternoon I was out working on my in-frame receiver and my wife came out and asked me "When will you be finished?"

I said "about 15-20 minutes." (foolishly thinking that she was referring to an impending meal....:doh: )


She replied "No, with the truck"

:o :o :o

What was your answer to that? :)
 
Back
Top Bottom