DUI install advice/questions

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 27, 2007
Threads
252
Messages
2,351
Location
Alabama
I recently acquired a DUI with the live wires. I’m going to install in my 1971 Fj40. It came with super generic instructions. I’m not getting it.
It mentions not bottoming out the dizzy... I’m wondering what’s the difference of completely seating a dizzy and bottoming it out.
Additionally, there’s no way to mount this to the block.... I have a thin metal sleeve from another old dizzy. It’s about 1/2 inch tall. Maybe this keeps me from bottoming it out?
Then, the top of the cap is not numbered. The wires, that are disconnected, are.
And finally, as far as timing, it mentions pointing the rotor to the firewall but ensure it spins towards the fourth cylinder.....
Any ideas or simplified techniques? Thanks!

4E12A7B1-AD5C-4C0E-8872-F10C27C17E88.webp
 
Then, the top of the cap is not numbered. The wires, that are disconnected, are.
And finally, as far as timing, it mentions pointing the rotor to the firewall but ensure it spins towards the fourth cylinder.....
Any ideas or simplified techniques? Thanks!

I doesn't matter which distributor post you use for the #1 cylinder, as long as the firing order is correct. When you stab it into the oil pump drive gear, position the cap and vacuum advance diaphragm where convenient (pointing forward or away from the block, not into the block). Then hook up the plug wires the same as your stock cap (in the same place and order).

Pointing the rotor towards cylinder/spark plug #4 when cylinder #1 is at TDC on the compression stroke will mean that you should only have to turn the dizzy a small amount when you set the timing with a timing light after starting it.
 
I hope you’re right Brian. She fired right up.
 
Addressing the “bottoming out” issue. It is important and it refers to the bottom end of the distributor shaft. The shaft is round but at the very end it is ground flat similar that of a flat blade screwdriver. As you insert the distributor, the flat ground tip enters the slot in the oil pump while at the same time the gear on the dizzy shaft meshes with the gear on the cam that drives it. The flat part of the dizzy shaft is only so long and can enter the oil pump slot only so far and then will “bottom out”. The mounting flange of the distributor should contact the engine block just before it bottoms out. Your Performance Distributor’s DUI should have come with a gasket that will fit between the engine block and the distributor’s mounting flange. To check for “bottoming out” you can insert a very small size feeler gauge or even a piece of paper between the block and the distributor’s mounting flange. With a little down pressure on the dizzy by hand, you should be able to trap the feeler gauge or paper from being able to pull out. If you can pull it out easily, then you are bottomed out and some shimming may be required. My Dui will bottom out without the gasket but is fine with the gasket installed.

That was a lengthy explanation, but I hope it helps.

As far as the mounting and lock down mechanism, I can snap some pics in the morning as my DUI dizzy happens to out right now while doing some other work on the rig.

EDIT: Forgot to mention. If the dizzy is bottomed out you will exert excessive pressure on the dizzy bearings which will most likely fail prematurely.
 
DUI, LiveWires (timing at 12* BTDC) and Denso (3013) W14EXR-U plugs (gapped at .050”), Mark rebuilt and tuned carb and my rebuilt 2F runs smooth as silk, at 75mph, on 31x10.5R15s.

I try to keep her at 60-65, but I have to give her her head now and again.

I can’t recall where I found my hold-down clamp... somewhere local I think... O’Reilly or Autozone, I guess.
 
Addressing the “bottoming out” issue. It is important and it refers to the bottom end of the distributor shaft. The shaft is round but at the very end it is ground flat similar that of a flat blade screwdriver. As you insert the distributor, the flat ground tip enters the slot in the oil pump while at the same time the gear on the dizzy shaft meshes with the gear on the cam that drives it. The flat part of the dizzy shaft is only so long and can enter the oil pump slot only so far and then will “bottom out”. The mounting flange of the distributor should contact the engine block just before it bottoms out. Your Performance Distributor’s DUI should have come with a gasket that will fit between the engine block and the distributor’s mounting flange. To check for “bottoming out” you can insert a very small size feeler gauge or even a piece of paper between the block and the distributor’s mounting flange. With a little down pressure on the dizzy by hand, you should be able to trap the feeler gauge or paper from being able to pull out. If you can pull it out easily, then you are bottomed out and some shimming may be required. My Dui will bottom out without the gasket but is fine with the gasket installed.

That was a lengthy explanation, but I hope it helps.

As far as the mounting and lock down mechanism, I can snap some pics in the morning as my DUI dizzy happens to out right now while doing some other work on the rig.

EDIT: Forgot to mention. If the dizzy is bottomed out you will exert excessive pressure on the dizzy bearings which will most likely fail prematurely.
Super helpful, thank you.

I have a DUI going on my 2f and I think I’m bottoming out because I definitely have a gap - maybe 1/8” - between flange and mount on block. Any idea how common it is to bottom out and what causes it? Meaning, are the receiving ends where it connects to the oil pump manufactured with different “depths,” or the shaft where the flange makes contact different lengths on different blocks?
 
Correction, I do NOT have an 1/8" gap. It's more like maybe .004" -which seems about right with the press and pull out test you described. Looks like I'm good, but still curious on the reason why there are differences across engines/dizzies.
 
Correction, I do NOT have an 1/8" gap. It's more like maybe .004" -which seems about right with the press and pull out test you described. Looks like I'm good, but still curious on the reason why there are differences across engines/dizzies.
.004" without the gasket would be good if you then install the gasket. That way when you tighten down the dizzy, it will not put pressure on the dizzy & pump bearings/bushings.
 
still curious on the reason why there are differences across engines/dizzies.
I would think those differences are slight and simply due to manufacturing tolerances.
 
Back
Top Bottom