driveshaft/diff flange - removal?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 9, 2004
Threads
65
Messages
598
Location
Flagstaff, AZ
I have searched both the forum and my Haynes and FSM, but haven't found the answer I am looking for. Hope you all can help me out.

I am changing to a 4 speed and need to change the flange on my front and rear differential but curious how to remove the nut holding them on. (I tried to take a picture but my camera didn't like being left out in my truck last night and didn't want to work.)

On the nut is a dimple where it looks like Toyota just used a punch to keep it locked in place. Is there a special tool or trick to get this dimple back out so I can remove it?

When I put this nut back on, what torque setting do I use?

I did read to use blue locktite on the driveshaft bolts to reinstall.

I will be replacing the seals once I am in there.

I would guess it is pretty straight forward once I remove the nut. Any other coments/suggestions?

Thanks,

Brian
 
I've used a punch to straighten out the dimple. Then used a long breaker bar or my electric impact. I have a FSM manual at home and can get you the torque specs tonight. Hopefully you have a heated garage to work in. I replaced my clutch in the winter time in Flagstaff outside. That was back in the seventies when Flagstaff got snow in the winter.:rolleyes:


John
 
John,

That would be great if you could get the torque settings. I couldn't find them when I looked but that doesn't mean they aren't in there.

Yep I have 2 big heaters in my garage that warms it up nicely. No snow to speak of this year - forest fires here we come...

Brian
 
I've got a cabin south of Flagstaff and was lucky enough to be up there for the big:rolleyes: snow we had a couple of weeks ago. I just can't wait for this year's fire season to start. Oh I forget it already started this week.

Are these the axles from the 71? Are they stock diffs? I've got a couple FSM covering different years.

John
 
Castle nut/cotter pin pinion nut: 160 foot pounds


Stake nut pinion nut: 145-173 foot pounds




I made a tool similar to what is in the FSM to hold the companion flange when I am torquing the pinion nut...It would work to hold it while trying to remove the nut also.




Air tools are your friend.



Good luck!


-Steve
 
John,

My axles and diffs are from a stock '71 but putting driveshafts from a late '70's rig for the 4 speed.

If you ever bring your 25 up this way - let me know - I'd love to see it.

Brian
 
Poser said:
Castle nut/cotter pin pinion nut: 160 foot pounds


Stake nut pinion nut: 145-173 foot pounds




I made a tool similar to what is in the FSM to hold the companion flange when I am torquing the pinion nut...It would work to hold it while trying to remove the nut also.




Air tools are your friend.



Good luck!


-Steve

Poser,

First - thanks for your great advice. You have no idea how much I have learned from you over the last couple of years on this site.

Is the nut w/ the dimple I am referring to a "stake nut pinion nut" that you referenced?

And finally, what page/chapter is this on in the FSM? Or are these numbers in your head?

Brian
 
Brian

The pinion changed from corse to fine spline in 78 I believe. You might want to make sure your new flanges are corse splined. I also thought a 71 would still have had the cotter key. I just remove the Ebrake backing plate off my 73's transfer case and it has the cotter key. Did you install the disc brakes on the front axle? Is it a later axle (76+) with stock disc brakes?

John
 
You are welcome. I am glad that I have been able to help....



Your 'dimple' nut is a stake nut.....


Those numbers came from:



Castle pinion nut:

Toyota chassis and body manual number 98041, section 4, page 12.



Stake pinion nut:

Toyota chassis and body manual number 98154E, section 5, page 23.




Oh, and yes, they are in my head.....


Good luck!



-Steve
 
Note also that I have been told that the stake nut should not be re-used -- rather you should use a new one. Also, a question I have to add is whether the flange for a "crush-sleeve" R&P is the same on the inside as the flange for a "shimmed" R&P? Also, if you are going to take the flange off, you should probably replace your pinion seal, and be sure to check a used pinion seal to be certain that it is not grooved.
 
John,

You know, I think the flanges I have are fine splined. I'll verify that on Sunday night when I get back home from traveling.

My rig does have the castle nut and cotter key on the tranfer case/ebrake side, but the diff side (only looked on the front) is the "dimple" nut.

The disc brakes I have are MAF conversions.

Brian
 
rgentry said:
Note also that I have been told that the stake nut should not be re-used -- rather you should use a new one. Also, a question I have to add is whether the flange for a "crush-sleeve" R&P is the same on the inside as the flange for a "shimmed" R&P? Also, if you are going to take the flange off, you should probably replace your pinion seal, and be sure to check a used pinion seal to be certain that it is not grooved.



The pinion seal should have a groove.... ;)


The companion flange however, we do not want a groove in that. :)


There is no difference in companion flanges other than bolt patterns.



I also use red locktite on all companion flange nuts....cotter pin or stake nut.


Good luck!


-Steve
 
No John, I am not stating that they are all coarse spline...


Yes John, you are correct that there was a spline change in 1978, from the coarse spline to the fine spline.


I did not read his question that deep, only about the comparison that he stated...


I read his question to be a difference between a crush sleeve companion flange and a shimmed flange. They are interchangable, as long as the splines are compatible. :) (There were shimmed flanges that were fine spline, as well as coarse.)


Sorry for not being kleer.
 
In '78 they switched from coarse to fine.

My '78 was built in Sept '77 and is equipped with coarse spline pinions/

Brian,

While you are in there, you may as well verify that your shims are good - not spun. If they spun, you will not get the correct bearing pre-load and your pinion bearings will fail.

Guess how I know this... :mad:
 
Back
Top Bottom