Dripping new hoses

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I ordered some Toyota clamps for the firewall hoses. The spring clamps are no longer stocked so had Toyota provide me with what they have. They gave me these, I do NOT recommend them. Had three leaks with them after rebuilding the engine. Go with constant tension band clamps. The spring clamps work great IMO but the wire hoops were nothing but a problem.

1153772


Like these constant tension clamps:

View attachment 1179215

Interesting. I say it's user error. Those are the clamps that I was talking about. Literally every 80 series ever made came with those clamps on various hoses. For the record, I've never had a leak with them...
 
Interesting. I say it's user error. Those are the clamps that I was talking about. Literally every 80 series ever made came with those clamps on various hoses. For the record, I've never had a leak with them...

One yes, three... Not likely. They did not like the rear heater hoses, could not clamp down efficiently and conform. Luckily I had not replaced the hood yet and had "easy" access. No other issues with the other clamps though and replaced every one of the wire clamps. They may have been too big but even then, I tried to tighten the heck out of them and they still leaked.
 
There are multiple sizes of those clamps...
 
I've had those clamps on my rear heater hoses for probably 10 years... Give or take a year.
 
I had to tighten my worm gear clamps on my rig as winter approached.back in may did head gasket.thought I got the clamps tight on heater hoses and rad.I got them what I will call summer tight. hoses were expanded due to heat here in ga during summer and noticed I was losing small amounts of coolant as winter approached.all screw clamps in this thing were loose except the breeze ones on fire wall and phh, allowing coolant to weep out when engine was cold.now I got them winter tight rubber has now contracted down in size most were quarter turn or more loose no Leaks now
 
Constant tension clamps ordered. Going to attempt to do this over the holiday weekend. It is now just leaking(drips) from 2 hoses. One on the firewall, pass side at the entrance to the wall. The other is the lower radiator hose.

I am also now running some Toyota pink(premixed). But what ratio of Toyota red(not mixed) should I run once I get this straightened out.


Sent from my iPhone
 
Constant tension clamps ordered. Going to attempt to do this over the holiday weekend. It is now just leaking(drips) from 2 hoses. One on the firewall, pass side at the entrance to the wall. The other is the lower radiator hose.

I am also now running some Toyota pink(premixed). But what ratio of Toyota red(not mixed) should I run once I get this straightened out.


Sent from my iPhone

Toyota Red vs Auto Store Green has been debated ad nausea. The consensus is to run green as it is readily available and red provides no benefit over green as far as performance.

But you have to flush the system thoroughly before switching between the two. I used a garden hose and running truck for 30 minutes flushing it all out after u had drained it. Then filled with distilled and drained. Then distilled and drained again. Then filled with green/water mix.
 
A multiple flush will be happening once I get the hoses figured out. I have read and read on red vs green. I run red in my tundra and will probably run red in the LC. I keep extra on the truck and will in the cruiser. But whether I was running red or green, what is the suggested ratio to run the coolant at on the 1FZ... 50:50, 60:30, 70:30?


Sent from my iPhone
 
I don't have a 1FZ so I don't know. But I would assume it's 50/50 but don't quote me...
 
The antifreeze usually says what mixture is require to prevent freezing at a given temp. More antifreeze than water equals lower freezing point. More water than antifreeze is cheaper and cools the engine better. 50/50 is typical, and is what you get if you buy "premixed".
 
Back
Top Bottom