Double Cardon Rear Shaft

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 21, 2006
Threads
34
Messages
349
Location
Bend, OR
I have a full 6" Slee lift. Have been running it for over a year and a half. I have a bad vibration on acceleration between 35-55mph. I have been going through u-joints (moogs) in the rear shaft every 6 months.
Yes I have adjusted the pinion angle and it sure looks right. Thinking of just switching to a double cardon rear shaft and using the stock one for a trail spare. Anyone know of a good place to buy one from or
have one made? Slee no longer sells them.
 
my $0.02: if you're going through u-joints that often, putting in a double Cardan shaft really won't solve your problem. It might hide it, but right now, those u-joints are sacrificial links in the mechanism. Replace them with something that can't break as easily and you might move the failure to a move a more expensive/critical component. Troubleshooting this may be a PITA, but time invested aside, it's free.

If it were mine, I might lean toward problem identification. You might still end up with the double Cardan joint solution, but then you'd know what you had.
 
It is a near certainty your pinion angle is off. Get a digital angle finder and figure it out. Did you get the adjustable upper arms?

A double cardan shaft means the angles have to be perfect-perfect in the sense that the pinion has to point directly and perfectly at the t-case output.

And also, higher operating angles wear out u-joints faster. Only use Toyota U joints. I don't know why but they are better.
 
I have See's 4" and had to put a double cardan rear in to eliminate bad vibes when tipping on and off throttle, running metal tech rear upper arms to set pinion and part time in front. I had a local, well respected shop fab one for me that does a lot of jeep and muscle car work. They used some high quality 1310 joint, I forget specifically which ones but I can find out for you if interested.

It's beyond me that Tatton has a good rep here, I ordered a rear shaft for an FJ60 from him a few years ago and the holes on the flange were a mess, they were misdrilled with two eclipsed bolt holes each. My previous experience with them was a poorly balanced front shaft for a jeep JK. Alternatively, I've had great success with Tom Woods phone-order drive shafts in the past, shafts had a nicer fit and finish and came well balanced.. if I was not going local that's who I would recommend.
 
It is a near certainty your pinion angle is off. Get a digital angle finder and figure it out. Did you get the adjustable upper arms?

A double cardan shaft means the angles have to be perfect-perfect in the sense that the pinion has to point directly and perfectly at the t-case output.

And also, higher operating angles wear out u-joints faster. Only use Toyota U joints. I don't know why but they are better.

I concur, everything I've seen indicates that Toyota U-joints are superior, however they're also a pain in the butt to change out compared to 1310's. I figured I mind as well have an engineered weak link, and something easy to fix at-that. Time will tell if it'll hold up but it's what the shop who built them recommended to me.. fingers crossed.
 
My 80 sits on a slee 4" lift but more
Like 5" until I load the vehicle for a trip.

I went round and round with pinion angle adjustments using a digital angle finder at home and verified a couple times at a very experienced and trusted driveline shop which I've had many Driveline's built by for various applications over 20 years and I never could eliminate the "grrrr" on deceleration. My rear shaft was at an operating angle of nearly 13*. The shop told me that past 6*-7* all some can be made to run smooth, some can't, and at that operating angle Ujoint life is reduced. The longer the shaft the more able it is to absorb vibes and run at steeper angles

With the 6" lift, your operating angle is even greater than mine, thus more challenging. Be aware that your pinion will need to be rotated up several degrees so it points at the transfer case output. This will cause your springs to touch their buckets at the forward part of the spring only. My springs now have a very noticeable bow to them and yours will be even more so. I have kicked around the idea of cutting the coil buckets off and repositioning them but truthfully, I can't tell any difference while driving or loading up.

Try to find a local driveline shop that uses only American made parts for the CV end. I think it's NeapCo that makes A 1310 CV that has a bolt pattern made to fit our outputs because good factory Toyota parts are getting scarce. Mine has the spicer Life series 1310x joint. No grease passages means is stronger than previous 1310 stuff. Been running mine over Rubicon for the past year with no problems. A lot of people will dismiss 1310 stuff as too weak and it definitely is not as strong as the over sized beast of a U-joint you will replace but proof of its strength and durability for our application is all over the Web on wheeling and hotrod and racing sites. And the fact that the cv and Ujoints are readily available doesn't hurt either. However, a long wear life would probably be realized with the larger joint.

Edit: After thinking about this some more, I wanted to add this comparison. The 1310 is rated at about 1600lbft yield strength where the 1350 is rated at about 2200lbft. I can justify the merits of the 1310 in the average 80 series based on my experience.

My last rig was a heavy Dodge Ramcharger with 1 ton axles, granny 4 speed, Atlas 4 speed T-case, 5.13's and 39.5 Irok's and fuel injected V-8. Double low range crawl ratio was 358:1. Now, we can assume that set up was applying much more than twice the torque to the driveline components than an 80 on 35" tires would. On that rig, I ran 1350 DC driveshafts, which are not double the strength of the 1310 joint, and I never experienced a U-joint failure. Add to this, an 80 has an auto gearbox which apply's torque smoothly and gradually. Driving style is a major factor but too subjective to be discussed.
 
Last edited:
I had rear driveline grrr myself with my 6" lift. Turned out under certain conditions the edges of the upper yoke were contacting the flange. It polished itself up real nice and haven't had issues since lol. I did however build new upper and lower arms to adjust pinion angle. A Double Cardan is a band-aid but sometimes it's the only way to get by. You could always try and get a driveline shop to setup the rear like the factory front in a broken-back configuration, may help. Either way, Toyota joints will last you longer not that moog is complete garbage, but I noticed I years ago in my 78 k20 Chevy I blew far fewer spicer joints than moog. Moog joints would last me a day on the mud flats and I'd have to replace them, spicer would usually last a few trips before giving up the ghost.
 
Adjustable control arms to change your diff angle and oem Toyota u joint to replace moog junk. Those joints just don't last on these rigs.
 
I'm on the same-ish 4" Slee lift as @baldilocks & with ~5" of lift out back I had an issue too & chased it in a different way.

Heavy 4" fr springs, Heavy progressive rr springs - decent 'stinkbug' unloaded even with a armor rear bumper & swingouts.

I lengthened the LCA's when I beefed them up and added the Slee adjustors to my UCA's - doing the lengthening & setting pinion angle fine-tune with the UCA's being threaded made for a perfect setup where I don't need a DC rear shaft (really wanted to avoid that) - so that was why I chased it as far as I did.
 
To answer your question, Jessie at High Angle Driveline.

As of a few years ago, he had a source for the OE 'ball and claw' as well as the Koyo's that Toyota never offered as seperate units, pretty sure he built Slee's shafts, and has the knowledge to tell you what you need, before you send him one arm and one leg, for a 'it works or it's free' shaft.

May have to call a few times, but a nice guy that knows driveshafts.

Edited: at some point, it's impossible to correct the issues without either modifying the transfer case placement or a custom drive shaft, i.e. D.C. shaft.

At certain 'lift' heights, the u joints operate at the outer edges of misalignment capabilities and will vibrate or wear rapidly. The D.C. joint effectively halves the angle on one end.
 
Last edited:
I appreciate the input from everyone. I do have the adjustable upper arms from Slee and I have adjusted them more than once. But I guess it's possible that I'm still off on the angle? Maybe I'll have to take it to a driveline shop and have them double check it. I was just under the impression that even with correcting the pinion angle to as close to perfect as possible, the angle with the 6" lift could still be too great. Hence the D.C. Shaft.
 
I second Tatton Driveshafts. Had him make a custom front DC shaft for my 100 series using 80 axles and it fit perfectly and got rid of my GRR noise at speed.
 
My 80 sits on a slee 4" lift but more
Like 5" until I load the vehicle for a trip.

I went round and round with pinion angle adjustments using a digital angle finder at home and verified a couple times at a very experienced and trusted driveline shop which I've had many Driveline's built by for various applications over 20 years and I never could eliminate the "grrrr" on deceleration. My rear shaft was at an operating anle of nearly 13*. The shop told me that past 6* all bets are off. Some can be made To run smooth, some can't and at That operating angle Ujoint life is cut in half.

With the 6" lift, your operating angle is even greater than mine, thus more challenging. Be aware that your pinion will need to be rotated up several degrees so it points at the transfer case output. This will cause your springs to touch their buckets at the forward part of the spring only. My springs now have a very noticeable bow to them and yours will be even more so. I have kicked around the idea of cutting the coil buckets off and repositioning them but truthfully, I can't tell any difference while driving or loading up.

Try to find a local driveline shop that uses only American made parts for the CV end. I think it's NeapCo that makes A 1310 CV that has a bolt pattern made to fit our outputs now because good factory Toyota parts are getting scarce. Mine has the spicer Life series 1310x joint. No grease passages and is stronger than previous 1310 stuff. Been running mine over Rubicon for the past year with no problems. A lot of people will dismiss 1310 stuff as weak and it definitely is not as strong as the over sized beast of a
Ujoint you will replace but proof of its strength and durability for our application is all over the Web on wheeling and hotrod and racing sites. And the fact that the cv and Ujoints are readily available doesn't hurt either.
I had shower thought this morning (where I do my best thinking): when the axle is rotated up from the pinion shaft-horizontal position, the fluid level, with respect to the pinion and spiders changes. Any thoughts as to how much?

I haven't tried to model the internal fluid-gear arrangement, but I'd think it was originally designed so that the pinion was half wet (or so) and all the spiders weren't completely submerged. If the pinion is now higher than the fluid level, and the spiders are all submerged, that might explain the growl. Not sure about the lubrication-life curve, probably won't be materially affected, but maybe food for thought.
 
The pinions need to be within 1 degree of each other. Get a digital angle finder from harbor freight for like $20. It has magnet for easy use. Maybe just the upper arms is not enough. Maybe lowers too. On up side the oem lowers bend easy. Aftermarket like metal tech will never bend

I appreciate the input from everyone. I do have the adjustable upper arms from Slee and I have adjusted them more than once. But I guess it's possible that I'm still off on the angle? Maybe I'll have to take it to a driveline shop and have them double check it. I was just under the impression that even with correcting the pinion angle to as close to perfect as possible, the angle with the 6" lift could still be too great. Hence the D.C. Shaft.
 
Last edited:
I agree with calling HAD and talking to Jessie about sourcing a new Toyota CV joint, I had heard he's able.

He'll tell you the same thing on strength and durability of Toyota joints vs whatever.

Probably also tell you that you're guess to as why you're having vibes is correct.

As for pinion angle, theres no way running a single joint shaft that hes having oiling issues. You're right, some diffs do run into issues with pinion bearing lubrication and being pointed real high but the yota diffs aren't too prone to pinion lube starvation. Overfill it some and it'll be fine.
 
I agree with calling HAD and talking to Jessie about sourcing a new Toyota CV joint, I had heard he's able.

He'll tell you the same thing on strength and durability of Toyota joints vs whatever.

Probably also tell you that you're guess to as why you're having vibes is correct.

As for pinion angle, theres no way running a single joint shaft that hes having oiling issues. You're right, some diffs do run into issues with pinion bearing lubrication and being pointed real high but the yota diffs aren't too prone to pinion lube starvation. Overfill it some and it'll be fine.
My thought was more that a "drier" gear might make more noise than a "wetter" gear, in reponse to @baldilocks earlier comments, and for general consumption in this thread.
 
I had shower thought this morning (where I do my best thinking): when the axle is rotated up from the pinion shaft-horizontal position, the fluid level, with respect to the pinion and spiders changes. Any thoughts as to how much?

I haven't tried to model the internal fluid-gear arrangement, but I'd think it was originally designed so that the pinion was half wet (or so) and all the spiders weren't completely submerged. If the pinion is now higher than the fluid level, and the spiders are all submerged, that might explain the growl. Not sure about the lubrication-life curve, probably won't be materially affected, but maybe food for thought.
Oil is being tossed all around the inside the diff. Probably less at lower speeds but less heat is being generated at trail speed. And besides that, the angle needed will not leave the pinion bearing high and dry.
 
Back
Top Bottom