Door rust repair

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 21, 2005
Threads
963
Messages
9,414
Location
Powell River, BC
I have some rust bubbling up on the outside bottom edge of my drivers door. I'm a complete noob when it comes to autobody repair so any suggestions much appreciated.

My current plan of attack would be strip the affected area with this "paint stripping" wheel I have for my grinder. Then pick up some kind of chemical rust prevention stuff (KBS coatings?) , paint over it and then spray some kind of creeping rust preventative inside the cavity.

Also have a small bubble forming along the top edge of the windshield as well. Hoping to not have to remove it, the glass that is!
 
I had and still have some superficial bubbling and minor through rust. There are many approaches to repairing the surface. I also live in central TX and I'm not concerned about is rusting again anytime soon.

For my LX450, I'm not real concerned about cosmetics or creating a perfectly level surface for new paint. I'm going to Monstaline the lower half and I wheel it. I also hate obsessing over shiny paint.

Ask yourself what outcome you want and start reading.

I used a couple different wire wheels on my cordless drill to remove the bubbled paint and rust until I hit clean steel. I then used a basic electric detail sander with 80 grit (because that what I had in my toolbox) to feather the paint edges out from the clean steel. I then put down 2 - 3 coats of self etching primer from a rattle can. I also sprayed a good bit of the self etching primer into the holes that had rusted through. This is all I've done so far. The purpose is specifically to stop the rust now and prep the surface for monstaliner. For the through rust I'm using JB SteelStick (on bare steel) for the very small holes and welding in new steel for the one larger spot (5" hole left by a trim screw that held onto some salt & water) on the driver side rocker.

POR15 is also a great product and I've used on another project. But, it's overkill for my purposes on my 80

BTW
...I'm not a body man and have never played one on TV.
 
IME if you have one "bubble" (read that as a rusty hole developing in the sheet metal) around the edge of the windshield you have a dozen more under the gasket; only fix is to remove the windshield and fix it properly. Has your windshield ever been replaced?
 
Clean affected areas and apply POR15. For the doors, concentrate on the inside then the outside. If you use POR15 on the outside, it needs to be painted because it is not UV resistant. For the windshield, cut the old windshield rubber, remove the windshield, clean and apply POR15, let dry, install new rubber with the old or a new windshield. The new OEM windshield rubber will cost you about 60.00.
 
Clean affected areas and apply POR15. For the doors, concentrate on the inside then the outside. If you use POR15 on the outside, it needs to be painted because it is not UV resistant. For the windshield, cut the old windshield rubber, remove the windshield, clean and apply POR15, let dry, install new rubber with the old or a new windshield. The new OEM windshield rubber will cost you about 60.00.
That's why I love this site - always good counsel on problems most of us will eventually have.
 
IME if you have one "bubble" (read that as a rusty hole developing in the sheet metal) around the edge of the windshield you have a dozen more under the gasket; only fix is to remove the windshield and fix it properly. Has your windshield ever been replaced?


I've never replaced it, no idea about it's previous life.
 
I'd sand the paint off the doors in the tiny area and use a "converter". since unless you sandblast, cut, or peel off the skin, you won't get it all. At the bottom of the door it's where the skin of the shell wraps over the inner part and it's probably between the 2 parts and inside the door too.
 
open it up with a pic, get some phosphoric acid to kill the rust / spray it up in there. I have used por putty for stuff like this and it has worked great. Then apply paint over the putty.

The cleanest option is to cut out effected rust and weld in new metal flush. That will require removal of glass and any rubber moulding.
 
I had a rust bubble on my front fender just above the fender flare that I noticed last fall. This is what looks like today after pulling the flare and chipping away the paint. That hole is not stk BTW. FWIW, I would suggest getting the rust fixed around your windshield right away if you plan on keeping it, otherwise you could be in for a very expensive repair or even scrapping it. Fortunately, I managed to repair my windshield rust on my own (with the parts from a donor HDJ81) even though I wouldn't consider myself any type of bodyman
image.webp

image.webp

image.webp
 
Back
Top Bottom