Diesel conversion

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Thats very exciting Jim!!!!!!!!!!!!!

I cannot wait to see this thing in real life and go for a ride in it. If not to big a incovience, next time I am in Vancouver I will give you a ring.

Two weeks ago we stayed in South Surrey White rock with our old friends, probably was not far from you.

Couple quciky qustions............

How did you deal with the fuel pump?
Did you try and interface the ECUs?
Was making the four wheel drive shift a big issue and is it connected into the ECU?
Lastly does the tranny truly work between the transmission and throttle sensor on the fuel pump?

I know you are swarn to secrecy on some of the wiring issues and will appreciate if you cannot share some of this advice.

Cheers
Rob
 
I recall Cdan saying you can order the plugs from Toyota, they got somekinda book to pick em out of.,

LX1HD-FT said:
I'm still wading through the electrical complexities of the diesel engine swap swamp.
Does anyone have a toasted 1FZ-FE engine wiring harness laying about? I'm looking for the 17 pin white plug that connects to its corresponding mate above the RH footwell near the Engine ECU inside the cabin. (see attached photo). With this plug I intend to leave the one inside the cabin intact and adapt the diesel engine harness to it.
Also, shamelessly, is a photo of the removed engine/tranny/tc which is low mileage, fully dealer serviced and up for sale.
Thanks,
Jim
 
Jim,

Does anyone have a toasted 1FZ-FE engine wiring harness laying about? I'm looking for the 17 pin white plug that connects to its corresponding mate above the RH footwell near the Engine ECU inside the cabin. (see attached photo).

Let me know if you get stuck as I may have one.

Bill
 
Rob,
When you're in Vancouver/White Rock next time for sure stop by and we'll go for a spin.

We left the gas fuel pump in and just hooked it to the fuel shut off solenoid wiring and all
works fine.

All the existing ECU's work. ie ABS, Cruise Control, Transmission Relay etc. The Diesel
ECU only functions as a emissions control(EGR) module and as the transmission control
module(TCM).

Re: your question about the four wheel shift, I'm not sure if I understand what you mean.
As I understand, the TCM receives speed sensor data and also throttle position data
from the the sensor atop the injection pump as you suggest. This provides the electronic
control (ie. shift points etc.) of the transmission.

Landpimp,
I appreciate the suggestion. I did ask Cdan and apparently that particular plug isn't available as a replacement part.

Photoman,
If you do have that plug I am interested in buying it. We used the one from my 1FZE engine in this diesel conversion and I intend to replace it in order to sell the 1FZE engine as a complete assembly.

Jim
 
LX1HD-FT said:
Hello Rob and all,
Yes the vehicle is on the road since last weekend. There are a few non-critical things to finish off. The tach isn't functioning yet and I may have to get a new tach and a European electric wiring diagram manual to resolve the issue.
The tranny power and second gear start also aren't working and WILL need the manual for that as there is a potential to fry the ECU/TCM if done incorrectly. Air con should be hooked this week. Raymond has been busy at other things so it's taking a little longer than planned to completely finish but I'm daily driving with it now. The thing has torque up the wazoo and the fuel econmy appears great. I haven't put a full tank of fuel through yet but have chalked up 650 km (404 miles) and still have a quarter of a tank left. I'll track fuel economy for a bunch of fill-ups and report the mpg later.
The power of the FT engine is about on par with the FZE engine. I challenged Raymond in his '97 lx450 on a freeway. We both were traveling at 80 kph(50mph) and accelerated flat out to around 140kph(87mph). We stayed pretty much even with me just slightly ahead.
Once I install an inter-coooler and tweak the injection pump I should be considerably faster but for the fact that he's soon to be swapping in his 1HD-T/5 speed/inter-cooler combo so we will probably still be at a standoff:-)
'Tho not a cheap project I'm really happy with the results.
Regards,
Jim

If you use a standard LC Turbo-Diesel engine you will never beat a petrol engine in top speed. The Turbo-Diesel has just 170 HP against the 212 HP of the petrol version :flipoff2: . And the standard diesel has only 160 HP. You will have more torque so ;) Anyway it is a nice project !

Mike
 
LX1HD-FT said:
Rob,
When you're in Vancouver/White Rock next time for sure stop by and we'll go for a spin.

We left the gas fuel pump in and just hooked it to the fuel shut off solenoid wiring and all
works fine.
Hmmm, I was told it would not work.

All the existing ECU's work. ie ABS, Cruise Control, Transmission Relay etc. The Diesel
ECU only functions as a emissions control(EGR) module and as the transmission control
module(TCM).
Did a ECU come with the diesel engine and if so are you using both the gas ECU and Diesel ECU?

Re: your question about the four wheel shift, I'm not sure if I understand what you mean.
As I understand, the TCM receives speed sensor data and also throttle position data
from the the sensor atop the injection pump as you suggest. This provides the electronic
control (ie. shift points etc.) of the transmission.

Is the TCM a seperate controler that came with the engine? I still have the auto transmission for the 1HD-T that I sold and have quite a bit of money tied up in it and would like to use it one day. Just need to know what I need for the install.

Thanks
Rob
 
Jim,

I will give it to you if it's part of the engine harness. PM me with your address etc. I will check later and make sure which one it is. Need to get some grub now.

Bill
 
Rob,

Did a ECU come with the diesel engine and if so are you using both the gas ECU and Diesel ECU?
Yes a diesel engine ECU did come with the engine/tran/tc and related harnesses which we used. That same ECU also contains the Transmission Control Module ECU. At some point in time Toyota changed from a stand alone ecu for the electronic A442F tranny to one that also combined engine functions as well. I suspect the change over happened when the 1HD-FT became available or more likely when the 1HD-FT got a computer controlled EGR system.
We didn't use the gas ecu which is identical in appearance and in fact three of the four plugs on the gas ecu plug into the three plug diesel one.

One general comment is that I don't think this 1HD-FT with automatic tranny swap would be feasible without the whole whack of harnesses etc. that I was fortunate to get form G&S Cruisers. As with most engine swap projects, having the whole front end of a donar vehicle would be the best way to go.
The 1HD-T/manual tranny is more straight forward but no a simple proposition either.


Photoman,
will do, thanks


Asiarider,
Your right I will never be as fast but I guess I can find solace in the fact that the diesel pulls harder with all that low end grunt.

Regards,
Jim
 
Here is a random question (kinda): What is the difference between a 1HD-FT Engine and a 1HD-FTE Engine?

Does an intercooler come with the 1HD-FT engine?

What kinda mileage are you getting now with the diesel engine?

And why is that accoding to $pector Off Road that the 1HD Engine has more power than the 1HD-T Engine?
 
Last edited:
Cruiser Newb said:
Here is a random question (kinda): What is the difference between a 1HD-FT Engine and a 1HD-FTE Engine?

Does an intercooler come with the 1HD-FT engine?

What kinda mileage are you getting now with the diesel engine?

And why is that accoding to $pector Off Road that the 1HD Engine has more power than the 1HD-T Engine?

Okaaaaay, as far as I know thier is no such thing as a 1HD.

As for the difference between a T motor and FT and FTE is the later FT has 24 valve head and the E at the end of FTE stands for electronically controlled. In otherwords for us to swap one of those babies in it would be a nightmare.

Milage wise I have been told by the Ozzy boys the T motor will get in the low 20s while the FT will get in the high 20s.

No factory intercoolers offered that I know of.
 
Radd Cruisers said:
Okaaaaay, as far as I know thier is no such thing as a 1HD.

As for the difference between a T motor and FT and FTE is the later FT has 24 valve head and the E at the end of FTE stands for electronically controlled. In otherwords for us to swap one of those babies in it would be a nightmare.

Milage wise I have been told by the Ozzy boys the T motor will get in the low 20s while the FT will get in the high 20s.

No factory intercoolers offered that I know of.

1HD-T 12 valve 1990 - 1994 HDJ80

1HD-FT 24 valve 1995 - 1997 HDJ80

1HD-FTE 24 valve, electronically controlled 1998 onwards HDJ100 with factory intercooler
and HDJ78/79 ute/troopy without intercooler
 
Radd Cruisers said:
Okaaaaay, as far as I know thier is no such thing as a 1HD.

Right it was a 1HZ!

I started calculating fuel savings and I'd save approximately $1500 per year if gas and diesel were priced the same. However, in Idaho right now gas is $2.03-2.10 and diesel is $2.49-2.58. So that pretty much negates any savings. However, I think I might still do it. I'm not sure how long the tax credit lasts for using alternative fuels but we can buy biodiesel in the pump at some stations now. That could be another plus.
 
LX1HD-FT said:
Hello Rob and all,
Yes the vehicle is on the road since last weekend. There are a few non-critical things to finish off. The tach isn't functioning yet and I may have to get a new tach and a European electric wiring diagram manual to resolve the issue.

Jim,

Nice conversion, I'm sure you're the envy of many Cruiserheads now :D
 
I have not seen Jims conversion in person, maybe on my way back up from Pismo I will drop by and see it. I hear Sheldon from G&S Cruisers who sold Jim the package was lucky enought to take the cruiser out, he was extremely impressed.
 
Greg,

I'm really pleased with the outcome for sure. I finally found a place in the Netherlands to buy the specific Electric Wiring Diagram supplementary manual to finish this off completely.
The EWD is crossing the Atlantic this moment. The company is All-American Imports and they are a specialist in Landcruisers. Among other things they produce a inter-cooler system for 1HD-FT 80 series which I'm going to get from them. There's a fellow in New Zealand, Craig Vincent, that has their system on his HDJ81 and recommends it.
I have about 5000 km on the LX now and now problems so far.
BTW, I understand you have a re-engined LC yourself. How about some details?

Widening the topic here a bit. Raymond, the mechanic that did my conversion has had his diesel converted Lexus LX450 on the road for a month now too. He went with a 1HD-T engine that he got from Rob at Radd Cruisers in Nanaimo, BC. He put a Toyota 5 speed tranny behind it, a 151F I believe, which he got, along with a whack of other bits, from Rodney of Wholesale Automatics fame in OZ. We did his conversion in my garage where mine was done and are calling it the Skunkworks now.
His swap went very fast and well. Because he had fully mapped out the harness interface for the worst case senario, mine(ECU controlled EGR system and Auto tranny) he was able to pre-wire his harness and was mostly plug and play. Some of the non-electric snags were as follows:
1. transmission tunnel cut out and adapted to accomodate the 5 speed.
2. modify and re-positiion the tranny cross-member
3. change the lengths of the front and rear drive shafts.
4. mount a couple of marine 12V solenoids on top of the fuel filter/separator for the starter
and fuel shut off switch.
5. install a fuel pressure regulator to reduce the high pressure from the stock in-tank gas
fuel pump. The high pressure was forcing fuel to leak out of the the fuel filter/separator
housing. I did't have this problem but opted to remove my in-tank pump anyway. I
adapted a pickup tube and screen from a ford diesel superduty pickup.

Hey Rob, it appears you were right on the pump removal issue. I had ordered a Walbro pump from Auto Performance Engineering in Texas. It was damaged in shipping and I returned it. The replacement has arrived now but mine has been driving fine without it. I'll probably install it when I put the inter-cooler in and tweak the injection pump.

It's getting kinda late so I'll wrap it up for now but will just add that if anybody in North America was to undertake a 1HD-T or 1HD-FT swap into a 8O series, Rayomond Fourier is the guy to talk to. He is a heavy duty diesel master mechanic and a works in the marine industry. He is also a rabbid cruiserhead and in fact used to own a Landcruiser specialist garage in South Africa before emmigrating to Canada. I will post some photos of his swap tomorrow.
Regards,
Jim
 
I tried to upload several photos of the Ray's 1HD-T conversion but can only manage this one because of board storage limits. It just shows the engine installed.

I also remembered a couple more modifications that were necessary on this and my swap.
A vacuum accumulator had to be made. This involved making a steel cylinder the size of the charcoal cannister and installing it in the cannister's bracket and plumbing it to the vacuum pump and the brake booster.
Also, the restrictor in the fuel filler tube had to be drilled out to allow the use of the larger diesel pump nozzle.

Hey Rob, anytime your in the area, coming back from Pismo or otherwise, stop by and we'll go for a cruise.

Jim
P1010174.webp
 
That looks real good Jim......

I was on my way up from Pismo and had all intentions of calling you, ended up in White Rock at our friends house in Morgan Creek. Little to much wine and before you know it the night was late I had forgotten to give you a ring.

Next trip over I will drop by.

Pismo was incrediable and I think if you had time next year you would thorougly enjoy the dunes and more so the people.

Rob
 
Lovely job - I think you should take it over to the dealer just to see their reaction when they open the hood....(picture teenage boy's breaking voice) "....hey mister, you've got the wrong engine!"
 
Ok to re-energize this thread, Jim what is the posibility that Ray will contract to do these swaps? If person brought a truck and HDT with H151?

Is something he would consider doing on the side time not being an issue?


Tom
 
Hello Tom,
Sorry for the delay. I haven't check this board for a while as I've been preocupied with swapping a turbo diesel into a G-Wagen.
PM me and I'll put you in touch with Ray directly.

Jim
 
Back
Top Bottom