Coolant Hose

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 26, 2019
Threads
7
Messages
64
Location
Houston, TX
Good morning,

Hope all is well.

I had been noticing a coolant drop in my reservoir over the past few weeks. Finally narrowed it down to a single suspect location, for which I am attaching images. On the surface of it, looks simple enough, however it is suspiciously close to the firewall and some A/C lines. I am sure someone has fixed this before, just unclear as to what to search for. I am basically concerned about nuances to be aware of, if any.
Thank you in advance!

C8C1F9B4-7141-4DA9-B725-5BBBF79B722A.webp


4843DE83-2DEE-4A4E-9421-BB5BAFCC7E9B.webp


C271E74D-D24C-491A-B804-55E4841D6493.webp
 
Some one added a flush port. Not oem. Replace the whole hose or put a junction into remove it
 
Good morning,

Hope all is well.

I had been noticing a coolant drop in my reservoir over the past few weeks. Finally narrowed it down to a single suspect location, for which I am attaching images. On the surface of it, looks simple enough, however it is suspiciously close to the firewall and some A/C lines. I am sure someone has fixed this before, just unclear as to what to search for. I am basically concerned about nuances to be aware of, if any.
Thank you in advance!

View attachment 2129495

View attachment 2129496

View attachment 2129497
Some one added a flush port. Not oem. Replace the whole hose or put a junction into remove it
Thank you!
 
While you are into the cooling system... and a good time to drain (including engine block and refill with new coolant...

The rest of the hoses up there and the heater valve are all original (the toyota sardine-can hose clamps). Those (especially the plastic heater valve) are time bombs waiting to fail and cook your motor. Likely the PHH has also never been changed.

I'd be spending some time going over all the various cooling/radiator hoses and making sure they are new.

Search this site/forum for heater valve and PHH and you'll learn what they are and why they should be replaced. There's also a coolant hose (well 2) that run to the throttle body (so a little hard to see) that should be on the replace list too.

cheers,
george.
 
While you are into the cooling system... and a good time to drain (including engine block and refill with new coolant...

The rest of the hoses up there and the heater valve are all original (the toyota sardine-can hose clamps). Those (especially the plastic heater valve) are time bombs waiting to fail and cook your motor. Likely the PHH has also never been changed.

I'd be spending some time going over all the various cooling/radiator hoses and making sure they are new.

Search this site/forum for heater valve and PHH and you'll learn what they are and why they should be replaced. There's also a coolant hose (well 2) that run to the throttle body (so a little hard to see) that should be on the replace list too.

cheers,
george.
Thanks for the detailed response. I just redid the pump, radiator, clutch and thermostat, flushed and replaced with red. But I agree that a lot of these parts that you mentioned look tired. Looks like this is going to be more of project rather than a quick fix.
 
Based on the information I found in the FSM, I am having a hard time deciphering what the correct parts would be for the entire assembly including the hoses, clamps and T-junction. Basically I have decided to replace the entire assembly shown below.
Could one of you wise ones perhaps guide me as to how I could get find the correct part numbers?

62EC19EB-E0E4-41B2-904A-BCF7C6301284.webp
 
Based on the information I found in the FSM, I am having a hard time deciphering what the correct parts would be for the entire assembly including the hoses, clamps and T-junction. Basically I have decided to replace the entire assembly shown below.
Could one of you wise ones perhaps guide me as to how I could get find the correct part numbers?

View attachment 2145101
There are two hoses that come up along the firewall over there, only available when you buy the hardlines they attach to on the bottom end. So you might want to go aftermarket Gates on those two. Also check this thread:

 
There are two hoses that come up along the firewall over there, only available when you buy the hardlines they attach to on the bottom end. So you might want to go aftermarket Gates on those two. Also check this thread:

There seems to be a disconnect from the hardlines that I was hoping to leverage. I will look into it. I honestly don't mind replacing the entire line, provided that I don't have to flush out coolant. I just added the Toyota red and it is expensive. Serves me right for replacing the entire cooling apparatus minus the lines.

Thanks!
 
There seems to be a disconnect from the hardlines that I was hoping to leverage. I will look into it. I honestly don't mind replacing the entire line, provided that I don't have to flush out coolant. I just added the Toyota red and it is expensive. Serves me right for replacing the entire cooling apparatus minus the lines.

Thanks!
Coolant is cheap. Blowing out a hose 50 miles from God-knows-where? Priceless.

Drain it, put it back in if you must. :)
 
Yeah, might be a good time to hit that PHH as well. Just got to figure out the right time so that I can wrap it up without my HOA flipping out.
Thanks,
 
Yeah, might be a good time to hit that PHH as well. Just got to figure out the right time so that I can wrap it up without my HOA flipping out.
Thanks,
Funny. Do the 52-inch Gates bypass in the Master Thread linked above. Best-case, you're done in something between 20 minutes and an hour. Gonna hafta drain the block, and have a bucket handy for the PHH disconnect. I blew three hours trying to replace the factory PHH with identical hose piece; complete waste of time.
 
Back
Top Bottom