Cold blooded.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 23, 2005
Threads
494
Messages
13,827
Location
Reno, NV
Website
forum.ih8mud.com
Morning temps are hitting 9° to 12° around here and my FJ40 is not warming up. I let it idle for 10 or 15 minutes and it still runs rough for 3 or 4 miles. This morning I shoved a piece of cardboard in front of the radiator, it warmed up in four or five minutes.

This is a 1975 (March) FJ40 with a 2F, I don't think it is the original motor since it has an oil cooler and I was told that wasn't introduced until 1976. I also had to trim the fan blades to fit inside the shroud. (When I bought the rig it had an electric fan that was way to small so I re-installed a mechanical fan. It took serveral tries to get one that fit.)

The fan has a clutch but I noticed that it was pulling air before the engine is warm.

So how do I test the fan clutch?

Or should I even worry about it? I've been doing the cardboard thing in the winter for years. It works fine. And I never overheat during the summer, even when lugging all day on the trail at 100° + temps.
 
You have the top gasket in place on the thermostat?
 
But you know about the top gasket, right? You have to order it separately, and if you don't get it in there, the thermostat will be bypassed and you'll have slow warmups.
 
But you know about the top gasket, right? You have to order it separately, and if you don't get it in there, the thermostat will be bypassed and you'll have slow warmups.

Yep, both gaskets in place.
 
Seems like it wouldn't make a difference whether your fan is blowing or not, unless the thermostat is open.

I know there are 170, 180, and 190 degree thermostats. Perhaps you have a 170?

I don't have a clutch fan. This morning it was 0 degrees, and the truck sits outside. I let it warm up for 10 minutes before I took off and was able to turn the hand choke off, the windshield was defrosted, and it ran smoothly.

I've done the cardboard trick before, too, when I forgot the gasket. 15 miles down the road, boiled over.
 
Seems like it wouldn't make a difference whether your fan is blowing or not, unless the thermostat is open.

I know there are 170, 180, and 190 degree thermostats. Perhaps you have a 170?

I don't have a clutch fan. This morning it was 0 degrees, and the truck sits outside. I let it warm up for 10 minutes before I took off and was able to turn the hand choke off, the windshield was defrosted, and it ran smoothly.

I've done the cardboard trick before, too, when I forgot the gasket. 15 miles down the road, boiled over.
I guess I could check the thermostat temp with a meat thermometer and a pan of hot water.

You have to cut a hole in the cardboard or use a smaller piece so there is some airflow.
 
I guess I could check the thermostat temp with a meat thermometer and a pan of hot water.

You have to cut a hole in the cardboard or use a smaller piece so there is some airflow.

Yeah.

Now that I think about it, I recall that the reason I went back to a stock exhaust from the headers I had was to take advantage of a functioning heatriser. I think I had significantly more trouble with cold running rough without it.
 
Yeah.

Now that I think about it, I recall that the reason I went back to a stock exhaust from the headers I had was to take advantage of a functioning heatriser. I think I had significantly more trouble with cold running rough without it.

Thats the Who Ha with the bi-metal spring that is supposed to move a damper dohicky but was rusted solid on mine. Right?

How is it supposed to work?
 
Thats the Who Ha with the bi-metal spring that is supposed to move a damper dohicky but was rusted solid on mine. Right?

How is it supposed to work?

That's it. It's a valve that directs exhaust gas to the underside of the intake during warmup, then closes when the engine compartment (well, the spring, anyway) gets warm. It doesn't make a noticable difference (well I don't think so) except in very cold conditions.
 
Does anyone know the actual warmed-up running temp (F) range for a 2F engine ? I'm running an OEM gauge and it doesn't show the actual temp.

I'd like to retrofit w/ an aftermarket gauge if possible, who stocks these?
 
cold

The header is your problem. There is a plate available from Manafree or Spector that bolts onto the bottom of the intake manifold with 2 outlets where you route the heater water thrrough and hot water warms the manifold. I made my own. It will warm up in 2 minutes.

Hope this helps. Bill
 
The header is your problem. There is a plate available from Manafree or Spector that bolts onto the bottom of the intake manifold with 2 outlets where you route the heater water thrrough and hot water warms the manifold. I made my own. It will warm up in 2 minutes.

Hope this helps. Bill

I think Degnol posted his home made heatriser design a few times as well.
 
That's it. It's a valve that directs exhaust gas to the underside of the intake during warmup, then closes when the engine compartment (well, the spring, anyway) gets warm. It doesn't make a noticable difference (well I don't think so) except in very cold conditions.

You mean opens when the spring gets warm.

Interesting. I'm restoring my original manifold and that thing looks like it takes up at least 20% of the already-small pipe when it's open. I've been thinking about cutting it out of there. I live in CA where cold is 30f, and this is not my DD.

The real bummer is that you have to cut it out. At mfg time they put the shaft through the cast iron, then welded the butterfly valve onto the shaft through the pipe, so it doesn't come out without some kind of hard, way-down-in-the-pipe cutting.

Even in the warm climes of NorCal my truck with headers is pretty cold blooded. I look forward to the exhaust manifold and stock carb.
 
You mean opens when the spring gets warm..


I guess it's a matter of semantics. Toyota sez "closes" in one paragraph, meaning one thing, the next it says "closes" meaning something else. :eek: It opens/closes relative to the intake manifold and does the opposite relative to the exhaust outlet.
hriser (Medium).webp
 
I guess it's a matter of semantics.

Yea. I see it as a valve in a pipe. The spring holds it closed. When it gets hot, the exhaust holds it open. I'm installing a block-off plate under the manifold anyhow, so the gasses can't go there regardless of the valve.


Now I've just got to figure out a better way to cut it out than a hack-saw blade with a duct-tape handle. On a '78 manifold it's about 6" to that shaft from either end of the pipe. Some kind of power cable saw that I've never seen would work great. I have to cut it twice too.
 
Last edited:
Yea. I see it as a valve in a pipe. The spring holds it closed. When it gets hot, the exhaust holds it open. I'm installing a block-off plate under the manifold anyhow, so the gasses can't go there regardless of the valve.


Now I've just got to figure out a better way to cut it out than a hack-saw blade with a duct-tape handle. On a '78 manifold it's about 6" to that shaft from either end of the pipe. Some kind of power cable saw that I've never seen would work great. I have to cut it twice too.

Could you drill the shaft out and plug weld the hole?


I wonder if just adding a blocking plate will help my situation?


Now that I actually have heat (via the cardboard method) I discovered that my DS defroster vent is blocked. The fun just never ends when your driving a thirty year old vehicle. :lol:
 
Back
Top Bottom