Code "24"

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 15, 2007
Threads
5
Messages
59
Location
Seattle
So I tried to start my 91 today and it jumped up to 1200 rpms, ran for about 2 seconds, then died. Tried again...same thing. Tried again but gave it gas, got up to 2200 for about 1 second then died. Checked the diagnostics and it gives me a code 24 (Intake Air Temperature Sensor signal). Any ideas what the heck is going on?Thanks
 
The FSM seems to indicate that the Air Temp. Sensor either is, or is part of, the Air Flow Meter (AFM). Do the on-vehicle test of the AFM (very simple; takes only a minute or two) listed on page FI-66 of the FSM.

Curtis
91FJ80, 240K
 
Try taking off the connector first and inspect the harness and pins around the connector. The pins in my harness connector got pulled into the cable when I changed the air filter. Maybe it's as simple as pulling the pin back out with some needle nose pliers.
 
What do you make of this?

The FSM seems to indicate that the Air Temp. Sensor either is, or is part of, the Air Flow Meter (AFM). Do the on-vehicle test of the AFM (very simple; takes only a minute or two) listed on page FI-66 of the FSM.

Curtis
91FJ80, 240K
Ok Ran the test. First time I was getting nothing, I took off the plate and one of the connectors was a little off. I gently pushed it back on and re-tested.FSM says- E2-VS ; 200-600 ; E2-VC 200-400 ; E2-THA 4-7k (for approx 32 degrees). I got 1200 E2-VS ; 280 E2-VC ; 3.8 E2-THA ( about 40 degrees out right now)So The connection helped BUT I am a bit high on the E2-VS. Does that mean it is toast? ps still wont stay running longer than 2 seconds.
 
Also.... I noticed that on the harness connector (female end) for the AFM, that there is no metal contact plate at the E2 position. Is that normal? OR should there be a metal contact point in every slot?
 
OK.....I adjusted the little brushes that are in there and the resistance is now about 480 on the E2-VS.....SO in theory it is good. But it still wont start.
So brainstorming here....since it starts (just wont stay running) it must not be the fuel or the spark. Especially since it is repeatable...ie if it were a fuel pump or something it would not keep starting, right? All hoses are attached and intact, so I woul dnot think it is an intake line or vacuume line. The MAF seems to be within spec now....assuming that is there anything else that would cause it to start...run for a few seconds then die? I am at my wits end with this thing.
 
Last edited:
Monkeyboy-

You should check the contacts inside the AFM next to the plug. Those are VERY delicate and WILL rip if disturbed.

See pic: (not my AFM, but very similar)
attachment.php
 
Monkeyboy-

You should check the contacts inside the AFM next to the plug. Those are VERY delicate and WILL rip if disturbed.

See pic: (not my AFM, but very similar)
attachment.php
Yeah all looks well. The E2 tab was out a bit but I just slipped it back under the contact and it worked fine. The little copper brushes were not making good conatact with the sensor (in the pic it is in the lower side left of center below the +), so I took that part off (the one with the hex head bolt) and got it to make better contact. Re-tested the resistance and it is in norm levels for all. But the symptoms are really unchanged. Still starts for a couple seconds then dies. If I start without any accelerator it runs for about 2.5 seconds. If I gun it, as soon as it gets to 2200rpms it chokes out like it is being starved of gas or air.????????it makes my brain hurt.
 
It might be fuel pressure regulator related but I don't know if forum members every got a code 24. Try doing a search using key words like FPR, CE 24, etc..., to see if anybody else experienced similar symtoms on those posts. Remember that fj62's have the exact same engine so don't just look in the 80's forum only. Please post your solutions and what else you've tried so people will know what was the problem.
 
The bogging and stalling is because the air flow meter is not seeing air that the motor is using. The iat sensor code will usually come on with just key on because the circuit back to the computer is showing open. If it didnt have the code I would be checking the intake boot, they love to split. But with the code I would say that you are missing supply voltage to the air flow meter. Basically, if you were to unplug the meter and start it code 24 would appear and it would run just like it is. Let me find a wiring schematic of voltages, and grounds and will post up in a while. I would bet on a broke wire in the harness.
 
Unplug meter and check this on harness side. With key on go from e2 to a known good engine ground. Is there 4-5 volts? If not wire broke or ecu not supplying voltage. If good go from vc to known good ground with an ohm meter is there continuity? Basically we are making sure your supply voltage and
41752039
grounds are present.
 
So this is what my wiring harness end for the AFM looks like. Is the E2 metal connector supposed to be missing. All others have metal clips for the connectors on the AFM except the E2.

There should be a crude paint drawing of this attached....hopefully.

Can someone pull theirs or verify this is what it should look like or should each "hole" have a connector in it?

84Cruisers pic may have shown this but for some reason I could not view it.

Thanks
AFM harness.webp
 
Its not showing up. Do you have voltage at e2?
 
Can someone pull theirs or verify this is what it should look like...

Ok; just pulled mine. It looks like what you're describing: No metal contact in the E2 slot.

Hey, tell us more about what you did before your trouble started. Did you actually start to unscrew the connector (which you now know is a very bad idea), or?? And what were you looking for? Just poking around out of curiosity?

Curtis
 
Ok Ran the test. First time I was getting nothing, I took off the plate and one of the connectors was a little off. I gently pushed it back on and re-tested.FSM says- E2-VS ; 200-600 ; E2-VC 200-400 ; E2-THA 4-7k (for approx 32 degrees). I got 1200 E2-VS ; 280 E2-VC ; 3.8 E2-THA ( about 40 degrees out right now)So The connection helped BUT I am a bit high on the E2-VS. Does that mean it is toast? ps still wont stay running longer than 2 seconds.

What about the E1-FC test on the top of page FI-67? Should be zero resistance when the measuring plate is in any position other than fully closed (and infinite resistance when closed).
 
Ok; just pulled mine. It looks like what you're describing: No metal contact in the E2 slot.

Hey, tell us more about what you did before your trouble started. Did you actually start to unscrew the connector (which you now know is a very bad idea), or?? And what were you looking for? Just poking around out of curiosity?

Curtis

Well A week ago now I Put in New plugs (NGK), New wires, new cap, new rotor, Cleaned and reoiled my air filter, cleaned the AFM with AFM cleaner, Seafoamed it, and replaced the right rear bumper corner. I bet it is that damn bumper!! here is a link to my original problem and what I have done so far. https://forum.ih8mud.com/showthread.php?t=191157

When removing the air filter I accidentally pulled those screws before I saw the clip.

It ran great for the last week ran it about 130 miles...then it just decided out of the blue to not start friday morning.
 
Last edited:
Back
Top Bottom