Code 0401 EGR flow insufficient--Safe to Drive?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 10, 2008
Threads
70
Messages
435
Location
Baton Rouge
Alright--my CEL light came on last night while the :princess: was driving it--her fault of course. Took it to the parts shop and got the 401 code.

I have searched and read all about the EGR system, but I am laid up after a minor surgery and can't work on the problem for a couple of weeks.

So is it safe to drive the vehicle until I have time to look at it? Will i cause damage by driving it with this CEL trigger?
 
mine has been on for a month and a half. Before you throw parts at it many have recommended taking off the throttle body and cleaning it good. Im gonna get mine next weekend i hope! best of luck with your recovery.
 
My truck had this code coming on at least once a week last year. I'd just reset it and keep driving. I finally got around to pulling the throttle body and cleaning the EGR port and it hasn't returned since (3 months).
 
i cleaned my temp sensor and it was off for about 3 weeks before it came back on. You know you just jinxed yourself and it will be back by the end of the week!
 
Welcome to the club :) I had the the same code and drove with it for several months until i had to renew my registration (inspection time). My issue turned out to be with the VSV. From what i've read, it seems the VSV is usually the culprit but I stongly recommend you follow the FSM steps to diagnosis this code before throwing money at it and replacing parts that dont need to be replaced. Oh yeah, SEARCH is your FRIEND!

PS. Nice avatar. I'm originally from ATL and use to see the panic boys quite egularly in the southeast!
 
shouldn't worry. i'm having the same code come up when my CEL comes on. i just go to autozone and turn it off. will take care of it when i get the FSM and then the parts i need.
 
shouldn't worry. i'm having the same code come up when my CEL comes on. i just go to autozone and turn it off. will take care of it when i get the FSM and then the parts i need.

My exact idea---if I could just find the FSM on the cheap...been looking for a while now with little luck.
 
My exact idea---if I could just find the FSM on the cheap...been looking for a while now with little luck.

It's about a $100. I think it would be a worthwhile investment. I just haven't picked up the phone to make the order.
 
Fellas,

No FSM, no DIY.

There is a current thread on the EGR with some well distilled info and some good pics. This ground has been covered and covered and covered on this forum.

Clean the tube through the intake. It probably needs it. Check all the lines for same. Once there is flow, you will be better able to detect which, if any, of the other components need attention. The VSV fails intermittantly, so you may test it and find it good, when, in fact it is not.

For me, with a good, professional, cruiserhead, mechanic (Chris Cole) working through the process with me, it was as follows with the "EGR Flow Insufficient":

1. EGR Vacuum Modulator replaced because filter had soot on it showing bad diaphram. Code came back.
2. Chris cleaned the passages(which were clogged solid) and tested the VSV for EGR, which tested OK, but according to Chris, could still be bad. Code came back.
3. Chris replaced the VSV for EGR. No code for a year and 15,000 miles.

Its a process, and its not a quick fix. Mr. T did not get this system perfect. But, considering the era of government emissions mandates and the need to cobble stuff to meet them when these trucks were new, we live with it and learn how to fix it.
 
My exact idea---if I could just find the FSM on the cheap...been looking for a while now with little luck.

I did the FSM download from the Toyota Tech website and got the whole manual 10 bucks. Took and hour or two, but well worth it.
 
CIL now off

To recap, the CIL came on about 400 miles ago. Pepboys pulled the p0401 code. I did nothing to fix the problem and this morning the CIL is off. Could this be due to the intermittent VSV failure as Ted said?

Other than the bulb burning out, why would the code/CIL disappear?
 
I have had 401 intermittently for about a year (on then off for about a month then on.. occasionally on off over a couple days or a week etc no particular pattern) sometimes it would clear itself - sometimes I had to clear it. I checked the easy things and then about 2 weeks ago decided to put an ohmmeter on the harness side of the VSV for EGR as suggested on one of the threads...bad reading .. Tried to put battery across the leads and no difference in the VSV behavior as required....after that check though the CEL goes on every two drive cycles ... VSV and gasket for throttle body are on order.


{Incidentally ... under the heading of "area 54" ... it may have been a coincidence .. or I was hallucinating ... or I forgot my tinfoil cap.. but I was beginning to think I noticed a correlation between triggering the CEL (401 code) and running under power lines... ah hell .. forget I said that!)
 
... VSV and gasket for throttle body are on order.

AJP's scenario is very common and is almost exactly the path that my truck took about 7 years ago. You do not need to remove the TB or the intake to R&R the VSV for EGR.
-B-
 
I found a bunch of hardened and one cracked vacuum hose under there. I don't know how anyone would be able to detect or replace this if they do not split the intake plenum. The hoses that needed replacement were the ones that wound up closest to the block when it was reassembled.
 
Thanks Beowulf...this "grasshopper" has read a lot of your previous mail on the VSV R&R and I definitely plan to try without removing any of the intake if I can. I have done a preliminary "recce" and cracked the bolts on the 2 brackets (manifold and VSV) in preparation for the VSV to arrive.

I also recognize that Sean's experience with bad vacuum lines and the need to check/replace is valid so I ordered some OEM vacuum hose as well. I was really hoping I might be able to restring new hoses working through the DS manifold gap (with the manifold bracket moved aside) and avoid pulling the TB.

No doubt the children in the neighborhood will have a vastly expanded vocabulary they won't be able to use at the dinner table when I am through!


(sorry added ... its a '97 LX450 with 240k kms...)
 
Fellas,

No FSM, no DIY.

Ordered mine today because this 1/2 ass :banana::wrench: doesn't understand half of what you all are talking about (i.e. what a plenum is). Most threads are just too technical for occaisional wrenchers like me. Hope some good illustrations within will clear up my limited mechanical vocabulary.
 
Most threads are just too technical for occaisional wrenchers like me.

Vocabulary can be a huge issue. Toyota calls a drive shaft the propeller shaft and universal joints are spiders. Here on 'Mud we will abbreviate to DS and uni or U-joint so this can get confusing in a hurry.

Feel free to ask for a translation after you get your FSM. Most guys will be more than happy to help someone that has gone to the trouble of buying a Factory Service Manual and still needs some assistance with some details.

-B-
 
Back
Top Bottom