Check your steering arm nuts

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 26, 2005
Threads
95
Messages
8,405
Location
Phoenix
Website
www.tralaz.org
This has been mentioned before, but it deserves a reminder- check the nuts that hold your trunion bearings in. I did the service on my front axle about a year ago, and recently one of the studs came up missing in action. Fortunately I had a bad axle seal on that side so grease soup poured through the hole and alerted me to the problem right away. I have seen threads about these nuts coming loose in the past, but figured it couldn't happen to me 'cause I torque and double-check everything- but it happened. All four nuts on the passenger lower trunion were loose with one stud completely gone. Driver's side was tight. The passenger side takes more abuse from the steering system, I guess that's why it came loose and the other side didn't. I'm gonna make an effort to check those when the wheels are off for whatever reason.

-Spike
 
Spike: Couple of fine-point questions.
  1. When you did your front axle service, did you replace the knuckle studs with the newer torx-head studs?
  2. If so, how tight did you torque the new studs?
  3. If so, did you use lock-tite on the new studs?
  4. If you did, did you use blue or red?
I'm just trying to figure out what might prevent my new torx-head studs from coming loose.
 
Spike: Couple of fine-point questions.
  1. When you did your front axle service, did you replace the knuckle studs with the newer torx-head studs?
  2. If so, how tight did you torque the new studs?
  3. If so, did you use lock-tite on the new studs?
  4. If you did, did you use blue or red?
I'm just trying to figure out what might prevent my new torx-head studs from coming loose.

No, at the time either the torx bolts weren't being used or I didn't know about them. I trusted in Toyota's engineering, and the cone washers are something I've always liked anyway. I can only blame my work as the original installation by the factory held together a lot longer than mine did. I suspect there may have been oil in the threads or something of that nature. On future axle jobs I will take further measures to insure that those nuts (or bolts, if I decide to go that route) stay tight- for instance I will remove all the studs, clean the threads thoroughly with brake cleaner, and use blue loc-tite on them. That won't keep the nuts on the studs though, and I'm reluctant to use loc-tite there, so I may switch to the torx bolts (why torx bolts, anyway? Anyone know?). I can't remember who came up with the torx bolts- kinda vaguely remember it might have been a Toyota fix, in which case my decision would be made for me. Someone posted a method to seat the steering arm (Idaho Doug?) which might have the effect of seating the cone washers as well- tapping on the arm between the bolts a few times as you tighten the nuts. I tightened them several times in a criss-cross pattern, and at the time I was pretty damn confident that they wouldn't come loose. So, check 'em.

-Spike
 
Spike, from what I've seen on these, what happens is that the stud is loosened when you dismantle the hub for rebuild, and subsequently, no matter how tight the nuts are, it's going to come undone. If you didn't double-nut, and then torque the stud itself back into the housing when doing the rebuild, that's probably what happened.

The torx-head studs are just easier to put in, and tighten--you still use the cone washers and nuts. All the torx-head does is allow you to more easily put the stud into the housing, and, potentially, to tighten it again, while the trunnion bearing and steering arm are attached to the housing.

Personally, I find the torx-head studs to be a much better design, because I don't like the idea of putting in a stud with double-nuts. I just don't trust the torque values, with that technique.
 
Miescha, when I did mine, I used the torque value from the FSM, Loc-tite Red, and, so far, zero loosening. The torque value is buried somewhere in the FSM, from what I remember. I want to say 90 ft-lbs, but that's from fallible memory.
 
I'm pretty sure it's the studs that come loose first and once loose so are the nuts. I had an on going problem with losening studs, last time it was down to one stud before I noticed. Two stud holes were oval instead of round. Took the swivel housing off, went to town cleaning the threaded holes, put new torx head studs in (previous ones were torx head) with lots of lock-tite and left it to set properly before re-installing on the truck. Couldn't torque two of the studs to spec because they felt about ready to go round and round for ever. That was probably about 2+ years ago and I still have to check them on a regular basis but so far no more problems. I think once this problem starts, cleaning the holes completely and lock-tite is the key. Now I have spare swivel housings for if this starts again.
 
I've developed the habit of checking them at each oil change while I'm laying under there anyhow. It's a reassuring thing to do. I've never had one come loose on a half dozen repacks, but it's still something I do.

DougM
 
I've developed the habit of checking them at each oil change while I'm laying under there anyhow. It's a reassuring thing to do. I've never had one come loose on a half dozen repacks, but it's still something I do.

DougM


I hit my caliper bolts too.
 
Good to information to know. Thanks for mentioning.
 
Back
Top Bottom