Carb-What should I do

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 6, 2004
Threads
234
Messages
4,449
Location
Bozeman, MT
I have an early f engine which has a 1 bbl carb it came with a rochester which ran but was crap so I took it off and put on a stock aisin which also has run at times but is apparantly crap as well. It seems to just dump excess fuel into the engine even though it shoudlnt, ex. when I shut off the engine the carb empties out. So I am trying to figure out what to do. Does anyone know if there is even a rebuild kit for these old 1 bbls? Also can you make/buy an adapter plate to put a 2 bbl on the engine? Does anyone have a working 1 bbl they want to sell? (pm me) Any other suggestions?
 
Last edited:
i just swapped my 1 bbl to a 2bbl.......jim c did the rebuild on the 2 bble and i cannot give him enough praise. i have the F engine and switched the intake to a 2F intake and now use a 2bbl car off a 74.
 
my cruiser is a 67. im not sure what you mean by round hole post a pic it please...
 
I'll bet Mark Algazy has what you need. Several guys here run the 1bbl and like it.
Marksoffroad.net


Ed
 
clemson55 said:
I have an early f engine which has a 1 bbl carb it came with a rochester which ran but was crap so I took it off and put on a stock aisan which also has run at times but is apparantly crap as well. It seems to just dump excess fuel into the engine even though it shoudlnt, ex. when I shut off the engine the carb empties out. So I am trying to figure out what to do. Does anyone know if there is even a rebuild kit for these old 1 bbls? Also can you make/buy an adapter plate to put a 2 bbl on the engine? Does anyone have a working 1 bbl they want to sell? (pm me) Any other suggestions?
The 1-bbl Aisan is usually rebuildable. Kit & float is still available from toyota.

2-bbl adapter plate onto 1-bbl manifold doesn't work well because the throat of the manifold is smaller then the 2 barrels of the carb. That means at WOT the carb is not the highest velocity, greatest delta P in intake tract.

Another suggestion would be to swap on a cylinder head, manifolds & 2bbl carb from a 1968-1972 F engine. Improves performance and efficiency.
 
i c what you are talkin about now. mine is either a late 67/early 68 then. or perhapse its not the original engine but im pretty sure it is. im not really positive that my cruiser is a 67 it has no ID plates anywhere. thats all i got man hope it works for yah..........
 
Toyota DID make a 2bbl intake manifold for the early Siamese port engines. MAF used to sell them back in the day when Harold Graves ran the place.

I've still got a couple of them on the shelf, including the last NOS one.
 
clemson55 said:
Mark could you shoot me a pm with the costs of a rebuild kit if you have one, and the cost of one of those intakes that will allow me to run a 2 bbl.
Thanks
Send the carb to Mark ... you wont regret it ;) My theory is: if it's early send it to Mark, if it's late send it to Jim. I tried rebuilding one once ...

:beer:

Tucker
 
I've heard nothing but good things about mark and jim, My dads a mechanic though and was working on cruisers when they were new so I trust him to rebuild my carb too. And since I'm a college student its a little more in my budget.
 
mark what do you charge for a single barel?I need one rebuilt for my '66
 
clemson55 said:
Mark could you shoot me a pm with the costs of a rebuild kit if you have one, and the cost of one of those intakes that will allow me to run a 2 bbl.
Thanks

Large window or small? If small, is it the one with the larger circle window inside a square frame, or the smaller window with an oval-ish retainer?

Not all of the 1bbl kits are still available, but I have a pretty good stockpile.;)
 
Back
Top Bottom