Bonehead Move ?: A/C compressor oil

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 27, 2014
Threads
13
Messages
115
Location
Beaufort,SC
Well, after years of no A/C in the south, I finally replaced my AC compressor and Dryer, new gaskets and went to get it charged up. Had I read the Denso site more clearly, I would have understood the oil procedure. I just read it had all the right oil all sealed up and bolted her right on, charged it and now worried I just doomed its life once again. This was atypical of me given I'm a newbie at mechanics. I usually read the instructions 52 times. I was hasty and arrogant. It held a great charge and is ice cold though!

How bad did I mess up?
Thanks in advance.
 
Well, after years of no A/C in the south, I finally replaced my AC compressor and Dryer, new gaskets and went to get it charged up. Had I read the Denso site more clearly, I would have understood the oil procedure. I just read it had all the right oil all sealed up and bolted her right on, charged it and now worried I just doomed its life once again. This was atypical of me given I'm a newbie at mechanics. I usually read the instructions 52 times. I was hasty and arrogant. It held a great charge and is ice cold though!

How bad did I mess up?
Thanks in advance.

I wouldn't be too concerned with the oil that came in the compressor IF it was stated that it was the correct amount for your system (about 8 ozs).

But I would have concerns if your system was not flushed prior to having a vacuum pulled and the system charged.

Time will tell. Its no trick to get cold air from a properly sealed and charged system. The longevity of your new compressor might be in question if the system (condenser, evaporator, TXV, lines) weren't clean before recharging.
 
Depends on why you needed to replace compressor. How much oil was in new compressor, most ship with a certain amount. There are charts for roughly how much oil you can expect your condensor and evap and lines to hold. That oil typically will not leak out with the refrigerant. Was the system open for a long period of time?

I’d be concerned that if your old compressor had failed, you have debris in system.

If your system was open for any length of time, you have debris in system.

If your new comp shipped with enough oil for the whole system, your overfilled with oil. If you didn’t lock up the comp already its probably fine, but can affect cooling.

If it didnt ship with any oil, youre low on oil which will reduce its life. Probably needs a few oz of pag 32
 
If your wallet allows you should just go to a shop with an ac machine, they can recover the gas you just put in the system so it is not wasted. Then they can get it flushed and do a vacuum test to make sure there are no leaks and add the appropriate amount of oil and fill it back up with your gas.
 
Depends on why you needed to replace compressor. How much oil was in new compressor, most ship with a certain amount. There are charts for roughly how much oil you can expect your condensor and evap and lines to hold. That oil typically will not leak out with the refrigerant. Was the system open for a long period of time?

I’d be concerned that if your old compressor had failed, you have debris in system.

If your system was open for any length of time, you have debris in system.

If your new comp shipped with enough oil for the whole system, your overfilled with oil. If you didn’t lock up the comp already its probably fine, but can affect cooling.

If it didnt ship with any oil, youre low on oil which will reduce its life. Probably needs a few oz of pag 32
The last shop I went to to have it serviced said it was blowing the dye everywhere and wanted to start throwing parts at it. It was working (just needed a clutch) but wouldn't hold a charge. I just decided to not go back to them. The system sat uncharged and untouched. Fast forward, I decided to start replacing the gaskets and got a good deal on a new Denso Compressor...probably just needed the new gaskets. I took it to a new shop after my blundered install and they hooked it up to a machine to do a 15 min vac then a 5 min hold. He asked after they filled up about the oil but didn't have any in the shop. Not going back to them either. All good. I have run it now for probably 5 hours drive time and still ice cold- no scary noises.
 
The last shop I went to to have it serviced said it was blowing the dye everywhere and wanted to start throwing parts at it. It was working (just needed a clutch) but wouldn't hold a charge. I just decided to not go back to them. The system sat uncharged and untouched. Fast forward, I decided to start replacing the gaskets and got a good deal on a new Denso Compressor...probably just needed the new gaskets. I took it to a new shop after my blundered install and they hooked it up to a machine to do a 15 min vac then a 5 min hold. He asked after they filled up about the oil but didn't have any in the shop. Not going back to them either. All good. I have run it now for probably 5 hours drive time and still ice cold- no scary noises.

Well if the compressor was dry, theres still oil in condensor and evap but that compresor won’t last as long as it should. It’ll probably still run a long time though. If it came with oil and its now overfilled with oil, it obviously wasnt enough to lock up the compressor so it’ll be fine but it wont cool as well as it could.

Either way, you’ll probably be fine for a good while. Just my opinion anyway...
 
Back
Top Bottom