Arb Swich Locations

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 7, 2004
Threads
20
Messages
145
Location
Oregon
I have ben searching but not much found. My ARB lockers are installed but I am tired of the switches hanging on the console. I need some ideas as to where to mount them.

Please, those of you that have ARBs, post some pics or descibe where you mounted the switches

Thanks
Lowell
 
I used an OEM Toyota rotary locker switch for my ARBs. IIRC, all 80 Series have the square knockout to the left of the steering wheel. There is also a standard switch knockout next to the locker switch that I used for the ARB main switch. I dig the OEM look.
 
I used an OEM Toyota rotary locker switch for my ARBs. IIRC, all 80 Series have the square knockout to the left of the steering wheel. There is also a standard switch knockout next to the locker switch that I used for the ARB main switch. I dig the OEM look.

Did you do a write-up on that? I'd be interested to see how it works.
 
I have ben searching but not much found. My ARB lockers are installed but I am tired of the switches hanging on the console. I need some ideas as to where to mount them.

Please, those of you that have ARBs, post some pics or descibe where you mounted the switches

Thanks
Lowell

The blanks under the HVAC control(where the rear heater switch is) can be popped out and the switches will fit in there. Also, the coin holders on either side of the large cubby on the center console pop out and the switches will fit there.

In both of these cases you may have to remove the plastic fake wood grain to remove the blanks.

Ary
 
Did you do a write-up on that? I'd be interested to see how it works.

No write up. I soldered pigtails onto the OEM locker switch with male spade connectors that mate to the ARB harness. Plug in and go. At the time the ARB switches would let you lock the front without the rear (not sure if this changed). The OEM switch locks the rear first and then both. Personally its just not a problem for me.
 
I was looking at the coin holders today and thinking they looked the right size. Thanks for the info on these.
 
my friend mounted his on the side of the center console where the heated seat switched would be on the 100 series
 
I moved the rheostat for the dash lights down to the unused plug next to the fuse cover and put the locker switches next to each other, see pic......
arbswitch.jpg



I put the compressor switch below the heater controls (sry no pic)
 
I used an OEM Toyota rotary locker switch for my ARBs. IIRC, all 80 Series have the square knockout to the left of the steering wheel. There is also a standard switch knockout next to the locker switch that I used for the ARB main switch. I dig the OEM look.

And if you don't mind some extra work, you can add a couple of relays and install the bulbs in the dash and have the factory locker lights come on when you activate the ARBs.
 
I put mine in the blanks under the AC controls. They fit perfectly into those holes. My buddy wanted me to put them in the coin slot holes on the center console. I thought that was a terrible idea. I have a 5 year old and those would be in a bad spot. She could reach them from her chair and when parked, if she's crawling around and hits them...fully locked in the grocery store parking lot would suck.

There is no "accidently" pushing them if they are in the dash.
 
And if you don't mind some extra work, you can add a couple of relays and install the bulbs in the dash and have the factory locker lights come on when you activate the ARBs.

Now that's cool. Not sure if the 91/92 had the lights in the dash. Might be worth a looksee.
 
Now that's cool. Not sure if the 91/92 had the lights in the dash. Might be worth a looksee.

Probably not there, since factory lockers weren't an option until 93.

Wonder if you could retrofit the gauge cluster from a 93-94 to a 91-92? Of course, you'd still need to add the wiring.
 
Probably not there, since factory lockers weren't an option until 93.

Yea, but my 91 has the knockout for the switch. I'll never get around to it anyway. Too many other things to do.
 
Back
Top Bottom