Land Speeder
InstaH8R
18" wheels and worn out 33's for your Hunnerd! I can bring them to Arkansas...
Toyota Tundra 18" alloy wheels BFG AT's
Toyota Tundra 18" alloy wheels BFG AT's
Anyone? - CLC Classifieds thread
- Thread starter Bodean
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Corrected it for you...
Last edited:
Guess I was kinda tired... Posted in the wrong thread. Sorry Greg
Last edited:
sorry Bossman...
I would have to agree with you!! Here is an old one I have at work pre-lift and pre-fender removal.
Last edited:
Bomar
SILVER Star
That sucks...sorry to hear.
Land Speeder
InstaH8R
Well, I went to see the 2 40s in Flowood.
The '76 has at least 1/4" of bondo on everything. There were no seams between the tub and top! It has no drivetrain and only has a rear axle. The body parts were all shot. The dash sheetmetal was good and it still had the steering column, guages, and a few switches/pulls.
The '78 was a little better. The hood was rusty and the windshield frame had what looked like fixable dents and little rust. Dash and rear tub were fair. Hardtop was rusty and drip rail was damaded and rusty. It had the complete drivetrain, but Wayne said it had 3.70 gears installed in both diffs. The front axle is a sought after disk brake axle. It has Dualmatic locking hubs and the original drive plates were in the drivers floorboard. The intake/exhaust/carb were missing. He would not budge off of $600.
If someone will buy this quick, I will help to move it and pay $125 for the tub. The axles, driveshafts, transfer case, H42 4-speed, what is left of the 2F, glass, dash, steering column/wheel, windshield frame, etc, etc should allow someone to make a little $$ or at least gain parts they need/want. I would buy it for $400-500, part it out and keep the tub, but I just don't have the room or time as the new job starts Monday.
The '76 has at least 1/4" of bondo on everything. There were no seams between the tub and top! It has no drivetrain and only has a rear axle. The body parts were all shot. The dash sheetmetal was good and it still had the steering column, guages, and a few switches/pulls.
The '78 was a little better. The hood was rusty and the windshield frame had what looked like fixable dents and little rust. Dash and rear tub were fair. Hardtop was rusty and drip rail was damaded and rusty. It had the complete drivetrain, but Wayne said it had 3.70 gears installed in both diffs. The front axle is a sought after disk brake axle. It has Dualmatic locking hubs and the original drive plates were in the drivers floorboard. The intake/exhaust/carb were missing. He would not budge off of $600.
If someone will buy this quick, I will help to move it and pay $125 for the tub. The axles, driveshafts, transfer case, H42 4-speed, what is left of the 2F, glass, dash, steering column/wheel, windshield frame, etc, etc should allow someone to make a little $$ or at least gain parts they need/want. I would buy it for $400-500, part it out and keep the tub, but I just don't have the room or time as the new job starts Monday.
fj40charles
SILVER Star
I've got four 20 pound aluminum CO2 tanks for sale. They're all full and tank is within certification date.
Can we swapped at any welding or beverage store.
Great for using around the house to blow dust off of home decoration, computers, etc.,
Can be used to air up tires and works well as shielding gas for mig welding.
$75 each. Cash or check. Can deliver to Cruiser Crawl in Hot springs if paid for in advance. Don't want to haul it up there and have the buyer back out. I'll get pics later.
Can we swapped at any welding or beverage store.
Great for using around the house to blow dust off of home decoration, computers, etc.,
Can be used to air up tires and works well as shielding gas for mig welding.
$75 each. Cash or check. Can deliver to Cruiser Crawl in Hot springs if paid for in advance. Don't want to haul it up there and have the buyer back out. I'll get pics later.
So will a regulator thread right on for welding? If so, I'll take one or two. PM me and we'll work something out; I'll be at the crawl.fj40charles said:
fj40charles
SILVER Star
You'll need one of these if your regulator has CGA 580 fitting. Around $15
Airgas - Radnor® 806 CGA320 To CGA580 Brass Cylinder Adapter
Here is one. Good vendor to deal with.
http://www.ebay.com/itm/Western-806...964?pt=LH_DefaultDomain_0&hash=item20b6cdb4dc
Look in Craigslist under Warren Wench or Waran Winch....it seems like they are always misspelled on Craigslist
Wanted:
Used tires for rollers.
Mandatory requirements: fits on a 15x7, holds air.
Prefer to have: 31" or bigger, matching set.
Would like to find some very soon but could pick up at SCC if needs be.
Used tires for rollers.
Mandatory requirements: fits on a 15x7, holds air.
Prefer to have: 31" or bigger, matching set.
Would like to find some very soon but could pick up at SCC if needs be.
hey steve not sure if this is what you want but...
http://jackson.craigslist.org/pts/2590328414.html I could probably have one of the CLC guys deliver to crawl if you wanted them. (I could give on price some) PM me if interested.
SHUSH said:
I appreciate the offer, but I'm really looking for something free or less than $50 for all 4. These are to put on a non-running truck to move around the yard only. Really hoping somebody had some old worn out tires that they just haven't yet sent off to scrap yet. Don't even need to have any tread on 'em - just need to hold air.