Another Starter Thread

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 10, 2020
Threads
15
Messages
92
Location
Birmingham
Okay, so hears the deal. I recently purchased my BJ40 with a period correct F2 engine replacement. Previous owner said that starter sometimes doesn't turn over. I haven't had a problem with it until today. I accidentally tried to start it in gear tonight. No biggie right? Well, now it won't turn over. Only a single click noise. The starter looks to be brand new. All grounds look great. No low battery issue. It only clicks once, no multiple clicks, so I am guessing its the solenoid. Since it is late. I can post pictures tomorrow, but I see no connections issues. Again, only a single click and no turn over. Clearly, the previous owner said that the lack of immediate turnover had happened before. Ignition switch issue, solenoid, something else? I have read all of the threads on point and have not found the problem yet. If this had occurred in the past, the starter looks to be brand new, and the grounds are all good, what is your guess? Any input is greatly appreciated. Thanks!
 
Last edited:
Old wiring, too much resistance. I suggest putting a $10 relay in line between the starter solenoid wire and the starter. VERY likely to solve your problem. Tons of threads on this cause/fix.
 
Hotwiring from starter solenoid spade connector and touching the other end directly to batt+ should give you an idea if the starter or solenoid are suspect.
[make sure it's in neutral first] And dodgy battery terminal connections can often give these symptoms.[and the main + heavy cable solenoid connector]
Fusible link is another thing to check if it's got one.
Annnnnnd, to cover all bases, check the back of the starter motor. On some starters There are 2 little screws that secure the motor shaft bushing end cap . make sure they aren't loose.
If it spins over from hotwiring, John mcvicker is on the right track.
 
Last edited:
Bendix Jammed in the flywheel I bet....bendix isn’t pulling back, Starter needs to spin up a bit befor it engages to have enough torque to roll the engine. Smack the side of the starter with BFH or try to roll the engine by hand counterclockwise (looking at the front of the engine). Been there, done that....good luck!
 
Okay, so hears the deal. I recently purchased my BJ40 with a period correct F2 engine replacement. Previous owner said that starter sometimes doesn't turn over. I haven't had a problem with it until today. I accidentally tried to start it in gear tonight. No biggie right? Well, now it won't turn over. Only a single click noise. The starter looks to be brand new. All grounds look great. No low battery issue. It only clicks once, no multiple clicks, so I am guessing its the solenoid. Since it is late. I can post pictures tomorrow, but I see no connections issues. Again, only a single click and no turn over. Clearly, the previous owner said that the lack of immediate turnover had happened before. Ignition switch issue, solenoid, something else? I have read all of the threads on point and have not found the problem yet. If this had occurred in the past, the starter looks to be brand new, and the grounds are all good, what is your guess? Any input is greatly appreciated. Thanks!


This is really very simple to deduce and explain , :

- The starter looks new right ?

- can you post some photos of it ?

- If it's NOT a OEM toyota NipponDenso parts maker Product or ASMO , there child company maker too ............

- then its a AUTO WORLD type generic or china brand , and there lies your problem ,a Low quality below toyota spec's unit

- ANYTHING other the oem toyota NippinDenso , Should Be considered RUBBISH and tossed in the Scrap Heap for the Master Blaster
and his Gang of thugs !


here is what you want :

TOYOTA 's new Mini Compact Direct Drive I offer , it Kick's Tail and is TOP SHELF GX Grade Mates ...........

hope this helps ?

matt


​
\
1598417067284.webp



1598417112092.webp




1598417175918.webp

​
 
Easiest thing to do is hook up a remote starter switch.

If it works, you’ve got faulty wiring or a faulty 45 year old ignition switch. If it doesn’t, probably the starter.

Like @ToyotaMatt I have experienced a ‘beautiful loser’ aftermarket starter. It LOOKS like a starter, and it’s really shiny. But it’s really a wheel chock.
 
Hotwiring from starter solenoid spade connector and touching the other end directly to batt+ should give you an idea if the starter or solenoid are suspect.
[make sure it's in neutral first] And dodgy battery terminal connections can often give these symptoms.[and the main + heavy cable solenoid connector]
Fusible link is another thing to check if it's got one.
Annnnnnd, to cover all bases, check the back of the starter motor. On some starters There are 2 little screws that secure the motor shaft bushing end cap . make sure they aren't loose.
If it spins over from hotwiring, John mcvicker is on the right track.
It spins over from hot wiring.
 
Bendix Jammed in the flywheel I bet....bendix isn’t pulling back, Starter needs to spin up a bit befor it engages to have enough torque to roll the engine. Smack the side of the starter with BFH or try to roll the engine by hand counterclockwise (looking at the front of the engine). Been there, done that....good luck!
Winner, winner, chicken dinner! I rocked the vehicle in gear a few times and hit the side of the starter with a BFH. Turned the key and rolled over once then the single click again. Repeated the steps and it started right up.
 
^^^
Not likely.

See your post #9 and Marks post #8.
 
Winner, winner, chicken dinner! I rocked the vehicle in gear a few times and hit the side of the starter with a BFH. Turned the key and rolled over once then the single click again. Repeated the steps and it started right up.
That tells me that the bushing in the nose of the starter is worn.....get a new starter....a gear drive....@toyotamatt’s looked pretty cool, got mine at the local Napa.
 
That tells me that the bushing in the nose of the starter is worn.....get a new starter....a gear drive....@toyotamatt’s looked pretty cool, got mine at the local Napa.
Yep. Time for a new starter. I might get Matt's, but which one did you get from Napa?
 
That tells me that the bushing in the nose of the starter is worn.....get a new starter....a gear drive....@toyotamatt’s looked pretty cool, got mine at the local Napa.
Mark,
I already have a Duralast Gold New Gear Reduction Starter on my truck. This thing looks to be pretty darn new. Any further thoughts?
IMG_E2840.JPG
IMG_2835.JPG
 
The starter I got from Napa was just a FJ60 gear starter, I think it’s actually a Nippondenso. Looks very similar to the pictures you’ve included.

Pull the starter if needed and inspect that. Since it’s a gear drive, it doesn’t have a bendix per say, but is extended into the flywheel by a plunger in the boxy looking piece under the motor.....basically the solenoid. There are a set of overrun clutches...just like an old fashion bendix....and a set of bearings/bushings that can wear and cause a misalignment...I’m thinking that’s your issue

What is your flywheel condition? Are the teeth on the starter ring still good? You can pull the bottom cover off and inspect?

If you can, chock up the wheels....triple check it’s in neutral....have your wife bump the key and watch the starter engagement from under the truck.

Without seeing the actual issue, kind of hard to troubleshoot from cell phone space. But I think it’s more mechanical than electrical.
 
Duralast is an AutoZone product...I rarely by hard parts from the Zone....usually head to Napa . I looked up your starter on Autozones web site and they quote new. However, from the Duralast web site:

STARTERS & ALTERNATORS
A car that won’t start puts a stop to your day. Duralast Starters and Alternators are remanufactured, replacing all wear components and mal-functioning assemblies, not just rebuilt with the original cleaned-up pieces. To ensure OE or better amperage and torque output, Duralast 100% triple-tests each part at the component, sub-assembly, and finished unit levels, so you can install with total confidence. And where the OE has known design flaws, Duralast develops an innovative solution.
 
I just had the exact same problem with my starter last weekend. I’m guessing the problem is the contact in your solenoid might be corroded. Unscrew the three bolts on the solenoid cover and a spring loaded piston will come out., There’s a copper (coated) washer on the piston that bridges the starter contacts when the solenoid is energized. It’s probably been arcing and the contacts are burned so the starter isn’t getting power. Bumping it while in gear and turning the key was sometime enough to move it and start it.
 
Last edited:
Duralast is an AutoZone product...I rarely by hard parts from the Zone....usually head to Napa . I looked up your starter on Autozones web site and they quote new. However, from the Duralast web site:

STARTERS & ALTERNATORS
A car that won’t start puts a stop to your day. Duralast Starters and Alternators are remanufactured, replacing all wear components and mal-functioning assemblies, not just rebuilt with the original cleaned-up pieces. To ensure OE or better amperage and torque output, Duralast 100% triple-tests each part at the component, sub-assembly, and finished unit levels, so you can install with total confidence. And where the OE has known design flaws, Duralast develops an innovative solution.
Thanks Mark, Matt, and everyone else for your input. I just went ahead and picked up a new starter from NAPA and installed it. It starts right up. The teeth were fine and so were the grounds. It must have been the bearings, bushings, contacts, or all of the above. 👍
 
Good job.....and out of curiosity.....the ‘tech support’ number on the starter, could you call it? I’ve never seen tech support phone number on a starter and just gotta know who picks up....LOL😎
 
Back
Top Bottom