AC Clutch?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 27, 2008
Threads
22
Messages
105
Location
New Mexico/Colorado
Load noise with AC on, its not the belt...how tough to fix :banana:??and how much moolah?

I need a :beer:
 
Howdy! The bad news is the clutch does not move when the A/C compressor is running. It locks up to drive the compressor. When it is not engaged, there is a bearing in the clutch that can make lots of noise. So, it sounds like your compressor is making the noise. Sorry. John
 
Hi,
As John said, often when the clutch bearing is going bad, you will get noise all the time, since the pulley spins any time the engine is on. If you get noise when the compressor is engaged, it is more likely to be the compressor, not the clutch. That said, a new clutch is $165, and a new compressor with clutch (OE Denso) is $325. A drier is $22.31 and expansion block (both Denso, also) is $44.71.
The good news is it's a straightforward fix.
Let me know if I can help,
Rex
 
The clutch bearing can be quiet when there is no load on it, but when a load is introduced it can become quite noisy. The bearings are cheap $ wise, under $5. If you can do the work, I can sell the part, if you can't, mail the compressor to me and I can do it. Denso has been making some s***ty compressors recently, take the 10S20F for instance, it's a complete pile of s***. They definitely changed the design for no good reason. The 10PA series was about as good as it gets. I'm guessing they tried to cut costs on the reed valves, and I bet 55 sells tons of those (the 10S) because of spiking head pressures or not enough suction.

If you have to replace the compressor, I'd go aftermarket before I went Denso, unless it's New Old Stock, which hopefully it is.

Yeah, I'm putting a second 10S20F on the same H2 that never left the shop! Neither the vehicle nor the compressor is worth a damn. Caveat emptor.

I'd be willing to bet that the internals of the compressor are just fine.
 
Last edited:
Funny, This just happened to me. Was having noise, changed belts, tension pulley, etc. Still squealed. Tightend, still.
Finally, last weekend my :princess: and I were going to meet a fellow cruiserhead for our last :beer: session before he moves back to Atlanta with his well known caged 80.

Her- "Honey, your AC is not that cold"
Me - "huh, yeah. WTF?"
Her - "does something smell?"
Me - "Uh, sorry... Wait, I smell burning"
(pulls car over, gets out, looks under hood)
her - "what is that smoke"
Me - "That would be the A/C Clutch"
Her - "Can we go back and get my car?"
me - "No, we're late."

Fortunately, my wife's Aunt and Uncle own an A/C compressor remanufacturing factory in Dallas, they just sent me a newly remaned Denso with clutch. Off to the shop tomorrow.
 
It happens. The clutch bearing going can create all the heat needed to ruin a clutch. Usually it melts the coil housing insulation on the clutch producing smoke. Catch it early enough and you don't have to spend much money. Once the electricals go, it's maybe $100, but probably closer to $70.
 
The clutch bearing can be quiet when there is no load on it, but when a load is introduced it can become quite noisy. The bearings are cheap $ wise, under $5. If you can do the work, I can sell the part, if you can't, mail the compressor to me and I can do it. Denso has been making some ****ty compressors recently, take the 10S20F for instance, it's a complete pile of ****. They definitely changed the design for no good reason. The 10PA series was about as good as it gets. I'm guessing they tried to cut costs on the reed valves, and I bet 55 sells tons of those (the 10S) because of spiking head pressures or not enough suction.

If you have to replace the compressor, I'd go aftermarket before I went Denso, unless it's New Old Stock, which hopefully it is.

Yeah, I'm putting a second 10S20F on the same H2 that never left the shop! Neither the vehicle nor the compressor is worth a damn. Caveat emptor.

I'd be willing to bet that the internals of the compressor are just fine.

Thanks for the response. it sounds like a 5 dollar part (bearings) is worth a shot...i don't hear anything until the ac is engarged which based on your comments sounds like the bearings are going bad...hopefully its nothing internal on the compressor. I can papal you the $$$ for the parts, just PM me and i will send and provide mailing address.

Kyle
 
Funny, This just happened to me. Was having noise, changed belts, tension pulley, etc. Still squealed. Tightend, still.
Finally, last weekend my :princess: and I were going to meet a fellow cruiserhead for our last :beer: session before he moves back to Atlanta with his well known caged 80.

Her- "Honey, your AC is not that cold"
Me - "huh, yeah. WTF?"
Her - "does something smell?"
Me - "Uh, sorry... Wait, I smell burning"
(pulls car over, gets out, looks under hood)
her - "what is that smoke"
Me - "That would be the A/C Clutch"
Her - "Can we go back and get my car?"
me - "No, we're late."

Fortunately, my wife's Aunt and Uncle own an A/C compressor remanufacturing factory in Dallas, they just sent me a newly remaned Denso with clutch. Off to the shop tomorrow.

Nice dialogue! How much can i get a remanned compressor with my Mud "family discount" ? :grinpimp::grinpimp:
 
TX,

I PM'd you. My 96 LX is doing the same thing when the AC is engaged. It growls at first engagement and gets quieter, but still noisey. How tough is the bearing replacement?
 
my compressor pulley seized while doing 60

plenty of friction and smoke...

bought a new compressor and drier.

how difficult is it to flush the system so i can put these on? anybody here done this before?
 
Back
Top Bottom