A750F Transmission issues

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Be aware the Transgo valve body kit is an "upgrade"; you're shifting will not be the same soft, smooth transition that is as when the transmission as new. If you want muscle car shifts, this is the way to go.

As I posted earlier, you really should exchange the fluid first, before spending time and money installing aftermarket parts. Draining and refilling the pan is not exchanging the fluid, no matter what anyone tells you.
Thanks for the response,
The first thing I did was dropped pan and changed the fluid and filter when the intermittent codes, hard shift in and out of second and eventually into limp mode. I was hoping the VB swap would solve it. To answer your question No I did not feel for wear or do a vacuum test. I am handy but not that handy.
My VB is at Trans Parts Tech outside Chicago. He wanted $320 for a refurbed one and I went with it. When he sent me the wrong one, mine has 7 solenoids and the one he sent had 6. My solenoids were fatter and the connecters were different. When I told him he wanted to see both so I sent them to him. The guy is nice but he is having problems finding one. Now he says he is going to rebuild mine because he can't find one. Again the guy is nice, he never dodged my calls but it's been like a month of him looking and I am not sure what I am going to get. I am looking for options and here we are.
Not sure if I want muscle car shifts I think I just want it original. Maybe the TransGo option is not for me.
Do you have any other recommendations? or where I could order one I can trust?
Thanks again for your time
Ian in Colorado
 
Don't feel bad about not being able to test the valve body. You have to have a vacuum pump and a test plate for the specific valve body in order to do that. It's not a setup that even the handiest guy would have in the garage.

Unless you have diagnostic trouble codes related to the valve body, you probably don't need another one, or even work on yours. Having said that, I don't know why he's having trouble finding a replacement for yours, it's listed on their website:
msedge_wspvpfAlWJ.webp

msedge_1mPh5H8Yey.webp

Again, changing the fluid is not the same as exchanging the fluid. There are two gallons of fluid in the system and you'll get, at best, 5 quarts out of the pan, even if you let it sit overnight. The engine, and thus the transmission pump has to be running in order to flush the old fluid out. The best method is to use the cooler loop, in front of the radiator, to drain and refill the system.

Using the exchange method, you'll flush the valve body along with the rest of the system, and your performance should improve.
 
Central Valve Bodies, in Claremore OK, also has refurbished valve bodies listed in their catalog.
msedge_vFnFOmi1EN.webp
 
They are also available new, but you have to get them form Japan. I'd suggest you contact Dave Stedman if you want to go that route. The part number is 35410-60520.
 
Don't feel bad about not being able to test the valve body. You have to have a vacuum pump and a test plate for the specific valve body in order to do that. It's not a setup that even the handiest guy would have in the garage.

Unless you have diagnostic trouble codes related to the valve body, you probably don't need another one, or even work on yours. Having said that, I don't know why he's having trouble finding a replacement for yours, it's listed on their website:
View attachment 4234645
View attachment 4234646
Again, changing the fluid is not the same as exchanging the fluid. There are two gallons of fluid in the system and you'll get, at best, 5 quarts out of the pan, even if you let it sit overnight. The engine, and thus the transmission pump has to be running in order to flush the old fluid out. The best method is to use the cooler loop, in front of the radiator, to drain and refill the system.

Using the exchange method, you'll flush the valve body along with the rest of the system, and your performance should improve.
Great information thank you
The one he sent me only had 6 solenoids and mine has 7 and the connectors and size of the solenoids were different. Whatever, the guy says he is rebuilding mine and I should get it next week.
With that said, I obviously have the pan dropped (well I have it up with no VB just to keep dust out) what would be my procedure to do a proper fluid flush to get the remaining oil out? reinstall VB and do the correct procedure from the front cooler lines? A little wasteful of oil but I really don't care at this point.
Yes, I am using true Toyota ws tranny oil.
Thank you so much for the response and help on this
 
At this point, you're stuck with whatever fluid is in the case, and with whatever is in the fluid. Without a valve body, there is no way to operate the transmission, and therefore, you cannot flush the case using the pump.

The problem you now have is that you're going to get a (presumably) very clean valve body and you're going to install it in a transmission which is full of dirty oil. Whatever's in the fluid now is going to be in the valve body soon after you start the engine. This is why I recommend flushing the entire system before you do anything, because then, at least, you have a case with clean oil in it.

Having removed the valve body, the only way to flush the lines is to remove the hardlines from the transmission case. This also requires removal of the cat(s) and really isn't worth it at this point, since all you'll be able to do is flush the hardlines and cooler loop. Whatever's in the case and torque converter are going to stay there, until you start the engine, after everything's back together.
 
Back
Top Bottom