94 93 vaf plug an play conversion split sec

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 5, 2014
Threads
8
Messages
230
I can't locate a air flow meter for my 94. I'm almost done with my build. I'm sure I'm not the only one out there. I spoke with split sec about a total plug an play bolt up maf conversion no wiring, knobs, or extra mini ecu. Just a simply built in unit an expoxyd sealed with ability to change out or use a used denso maf from like a Fj orTacoma 1fgr. I wanted to see if others are interested so I can show mark at split sec maf conversions in California there's a demand. With the conversion I would also think you could turbo supercharge more flow. Regardless we need a fix. I want to print off input from the site for research an development an demand of product. Feel free call Mark at split sec maf an explain the need.
 
I would be interested to see this happen. It would open up a lot of options if it were to be possible.
 
  • Like
Reactions: jay
Any news? I am interested as working vafm are impossible to find lately.
 
I spoke to Mark this morning. They can develop a kit for a 1994 land cruiser if some is willing to leave a vehicle with them to develop this kit. Any one local that can assist would be greatly appreciated. They are located in Santa Ana, CA. Contact information is below.

contact Mark at Split Second
1949 E Deere Ave.
Santa Ana, CA 92705
phone: 949-863-1359
email: sales@splitsec.com
 
I'm doing axles now an suspension next. I haven't forgotten. I need one. I emailed the piggyback ecu company in AU no response though. Bullet superchargers kit is 93 to 97 an uses a map in con junction with piggy ecu. I emailed bullet too no response. I was wondering if the map could be used to eliminate the vaf or is solo with super set up. I was also interested in a complete replacement ecu programed with a maf. The house can be CAD easy solid works an use existing set up an hose etc. I was also thinking about contacting Fuji enterprises Japan. Regardless in time the void will be filled the demand is high. Even more then most junk yards no about 80 series. Parts are in demand it's the next best thing to 40 series an only 60K for the states were produced in 5 year span. Fuji does the supra an SC300 in early years straight thru vaf. An carbs for the older lands. Aem has a stand alone for the supra I didn't try calling them. The carbed 1fzf came manual only there no kick down attachment.an 93 94 is eltronic tyranny need ecu. 1hz turbo kit an a 440f would fit wit know eltronics edm proof. An standard has dif cross member an cutting up the tunnel. Don't drill holes in the shifter console there golden with out cell phone holes . There a vinyl dash trim kit that will fit over it an wood etc. Well check in n. Mark needs get to it probly least in expensive rout for now. I think you could use Camry temp sensor in air box to conjunction with cold start. An there pilots Russia chip.I spoke with Mark months back toldem plug an play no knobs etc. He said oK toldem use a 1gr maf. An expoxy seal it in housing the electronics. Rember ecu can be serviced don't throw nothing away even vafs. My guy called corporate who relayed Japan said world stock is depleted at this time. Things do come back in stock after discontinued. Yota discretion an popular demand. The bad is the cost. An moving part in like a hot wire wit air over it. That qrc maf cleaner works good too. I would spray all cars with that stuff.
 
I'm probly 6 months more on my build it take a lot of time. Maybe less a lot of sourcing
 
I'm reading on it now even takes barometric readings. Says can install 2ND map barometric sensor. Can coordinate map an tps. I'm have to research this says programble. need a output for fuel pump kick cost around 400.00
 
Anyone on MUD that is running a Mega Squirt setup on either an OBD I or OBD II rig?
Not that I am aware of. Although plenty running standalone which is what this is. It is completely universal. Obd 1 trucks would be much easier because transmission control is through a separate ECU and you can simply wire in the engine control parallel while retaining factor ECU. So your factory ECU thinks it is working because it is receiving all the necessary inputs and the MS is controlling the outputs that run your engine. I plan to go this route if I do not sell my truck. I have used MS3 on other vehicles with great success in the past. One main reason for its low cost compared to other standalone systems is its 16 bank tuning window. Not ideal for race cars which is what mostly standalone systems are used for. But, for someone that wants total control over engine management in a cruise this would work great. I have used MS3 to make 600+ hp from VW VR6 engines with turbos back in the day. I have no experience with MS Pro which is their newer top ecu. It has a lot more features but none I see of value for a cruiser. If I keep truck I am going turbo and this route.
 
Back
Top Bottom