'70 Wiper motor electrics help needed

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Rainman

Wondering what my next vehicle will be...
Joined
May 25, 2013
Threads
112
Messages
2,186
Location
Nashville, Tennessee
Okay, first off, I'm no good at electrical stuff. So there's that.

The cover for this is missing and I'm fairly sure new ones don't exist. Is there an aftermarket solution? Has someone here made a new piece that replaces the old? IS there some other fix? I'm not sure exactly how those contacts work so I'm not sure how to solve it. The wipers do not work and I'm suspect that this is the reason.
Wiper detail.webp
 
If park plunger is missing, what's the fix?

@Coolerman , can I get a hand on this?

Is there a fix for this?
 
What did anybody here do when they had this setup fail like this one? Everything is perfect accept the connectors shown.
 
What did anybody here do when they had this setup fail like this one? Everything is perfect accept the connectors shown.

Well, take a look at the schematic for wiper high speed position. Notice the motor gets the ground from the WB wire. +12V always there to common brush. Only time park switch comes into play is when wipers are off. Then the wipers will continue until mechanical puts the switch into park position , no more ground. I suppose your wipers should work , but when off position they will not park.

Wiper high.webp
 
Here is a LINK to the wiper motor cover on eBay from a fellow mudder.
It looks like you are missing a contact on the park switch as well.
 
Just bought the cover. All 3 contacts are there. The middle one is just hiding behind the first one. Looks like I'm missing the "push rod" or whatever is missing from the small hole. The park plunger gizmo. Everything else about this assembly is perfect. I'd really hate to loose the whole thing because of something so small.
 
I do not know what the plunger looks like or its dimensions but it shouldn't be that difficult to fabricate. Find a suitable piece of metal rod (I assume its's metal and we all know what assuming does) and put it into the guide and bump the motor manually to determine the amount of travel. Cut the rod to the appropriate length and smooth the ends. Voila...a new park plunger.
 
If he’s talking about the piece I think he is, I don’t recall it being metal. Has to be nonconductive. It’s fibrous, as I found when I started filing it to clean it.
 
That makes the solution even easier. Get a piece of UHMW plastic rod of the appropriate diameter, available from Amazon or other interweb vendor if you don't have a local source. If you can't find the exact size then get something slightly larger and chuck it in a lathe if you have one or a drill if you don't and use sandpaper or files to bring it down to size. Cut to length and shape the ends. Should be easy to do with the average tools most 40 owners have.
 
Now we're getting somewhere. I have all the parts I need! Unfortunately I can't use any of them. Turns out the current build I have has these wipers and it's complete. So I took it part to see what I'm after. Well, just maybe someone can make some of these...
(Without my calipers handy.)
Shaft, maybe 2mm diameter.
Shaft is metal (about 8mm long)
Knob is some plastic kind of material. 4.5mm tall, 4.5mm diameter. Domed top.

I wonder if aluminum would work?

wiper park post.webp
 
A few questions and then I'll see if I can reproduce one.
What is the durometer of the plastic knob? Here is a LINK to a durometer scale .
What is the exact diameter of the shaft?
What is the exact length of the rod from end to the base of the rubber knob?
What is the exact height of the rubber knob?
What is the exact diameter of the knob at the base?
Any idea what color the knob is and if it is clear, translucent or opaque?
What retains the rod in the motor?
 
Your link failed.. I have no idea what what the durometer scale is.
 
Thanks!!

Try this Link.
 
By the way, those are mm measurements. Based on the examples on your link, I'd right off the bat I'd say the durometer measurement of the knob is easily 60 to 80. It's at least as hard as a caster wheel.
 
You are saying the durometer is Shore D 60 -80?
Are the dims in cm or mm?
Is it held in place by the park switch or some other retainer?
Thank you.
 
You missed my note. They are in mm.

Yes. Hard plastic or some other substance. I seriously don't think it's rocket science and has to be exactly the same.

It's held in place by the copper contact. No chance for it to fall out unless two screws are removed. 4 if you count the rubber cover.
 
Back
Top Bottom