40 to 45 transformations....

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 29, 2002
Threads
101
Messages
2,679
Location
nashville, tn
sup fellas,

been tryin to figure out what to do with my the rotting rear end of my tub...and i was leafing through a toyota trails last night. saw a pic of a real solid lookin 45 and i just decided that's what i am goin to do...


anybody have any pics of a conversion like this (i've looked at all of nolen's stuff when he redid kate over on pirate last year)?

i know that redrustbucket is in medias res on this right now, so i figure he could help me out with some stuff too.

here're the questions:

1. hardtop: i have a clean 40 hardtop that i think i'm goin to chop so that i don't have to buy anything else, ha ha. keep the liftgate too, as something a little different. what should i do abt the fiberglass dome? i should just be able to cut it and glass it back together right?

2. body mounts: for the rear of the cab, what have y'all seen or done? i assume that i could just fit it to the stock mounts of the 40 right where the floor of the tub takes that bend. if i want to stretch the cab a little bit more, would i be safe using those mounts if they're not at the very edge of the cab?

3. quarters: what should i go abt using for the quarters of the cab? i would like to keep a stock look, so i assumed i could just chop in my quarters and tub lip, but i know that there will be a lot of fab work to do with that as well...any suggestions?

4. spacing between cab and bed: i plan on making my own bed (at least for the time being) and i was wondering if clearancing it 1/4" to 1/2" will be fine.


i'm sure that i'll come up with many more questions as i keep grinding out the details on this, so don't worry, there will be more to follow, ha ha


malphrus

also, plans for the chassis of the rig include SOA, 55 rears and 40 fronts flipped (get as much wheelbase as i can), same ol' 2F, h55f/splitcase + some gear reduction box...(wishful thinking on all that, ha ha), beefed up stock axles, luke's steering arms, same ol' saginaw ps, discs in the rear, and 37ish rubbers...
 
1975 FJ40... tub was shortened, closed in using stock rear halfdoors, reskinne the corners, frame was lengthened at the highpoint above the rear axle. wheelbase is 113... just a hair too long, but it works quite well. 350/sm420 for now, with an NV4500/orion waiting.

scheck it:
 
sounds awesome...someone else has done it...but i'm not at home so i can't post pics. on the bed, i'd put 1 1/2 - 2 inches to keep the body from flexing into the bed. also, for the rear, just use the upper portion of your rear corners and a section of the upper rail you cut out and new sheetmetal below. now would be the time to do an extended cab also. what year? do you have the kickout windows on the hardtop?
 
i was just going to post the same question . i have a spare 40 also . sitting there with partail rotted body also would like to make some kinda stretched 40 /45 ,would love to see pics , my truck is sitting as a rolling chassis with only the firewall . but am also looking to put something together would like to go auto for my wife . presently it has chev 350 ,to stock 4sp. and soa . any pics on this conversion would be cool .

Jake
 
On VOR (:rolleyes: i know) there is a sweet looking conversion there, from 40 to 45swb:

1552.jpg


1554.jpg


1553.jpg


While I'd never buy that one, the idea is killer to me...
 
heck, i'll probably run the thing for 3 years without a bed...i went 9 months without headlights, anybody want to start a pool on that...?


i plan on makin the bed much narrower as well, with the most width only about 8 inches wider than the frame rails at the top of the bed....maybe full width right next to the cab so i can put a couple of jumpseats facing rearward. i also have planned on making a one piece tailgate out of my two barndoors (minus abt 10 inches in the middle section).


thanks for the pics y'all....keep em comin if you got em. (gifu, that's abt what i'm goin for...except wb around 100...)

i was lookin at about a foot behind the buckets up front for a frame of reference on the extended cab....i have a 72, so no dice on the pop out windows on the hardtop. i will definitely use the quarter windows (b/c they are baller) but i'm not sure abt anything else with the ext. cab.

have any of y'all messed with the fiberglass top? i've repaired holes and cracks in mine, but never a full width seam, so i'm not 100% sure on how that would work....


thanks again, and i'll keep y'all posted


malphrus
 
Is there any frame length difference between the 40 and 45?
 
I'll chime in on this, since that's what I looking at for my cruiser. My rig needs to be a farm work truck, flat bed preferred, that can handle moderate trails and maybe a few special highway trips to trailheads. Gifu's looks right but what's this about lengthening the frame at the high point over the axles? I was thinking of making the splice at the back door post just in front of the forward spring hanger for the rear springs. School me dudes!
 
the frame would need to be lengthed in the raised section so that the leaf springs can center the axle over the raised part.

this is needed if you intend to extended the wheelbase a large amount, but not necessary if you're just flipping the springs and moving the mounts to add 10 or so inches...

i'm thinking abt lengthening the frame, but more than likely i will not. it'll just be a stubby little mutt of a cruiser, ha ha.


malphrus
 
jesterb said:
Is there any frame length difference between the 40 and 45?


i'm pretty sure there is a significant difference in the frames b/c the wheelbase of the 40 is 90" and the wheelbase of the lwb45 is 116" IIRC...



malphrus
 
nuclearlemon said:
the frame is different on the 45.
this shot shows where dad seamed his half cab..his wasa 77 top cut right in front of the kick out windows.


how 'un-noticeable' will i be able to make the seam on the outside? i can just cover the inside seam with a headliner, so not that big a deal as long as it's not goin to leak and will physically hold the thing together, ha ha. i am worried abt the outside lookin like i cut it in half and fiberglassed it though (ha ha, duh...)

i've done basic fiberglass repairs and stuff like that to a couple canoes and boats and fixed my dome a couple times, but like i said earlier, i'm no fiberglass voodoo warrior or anything like that...


malphrus
 
I started a 40 to 45 project, but it went to a friend who is going to make a troopie style instead.(Traded him for a original45 cab he didnt want to cut up)
Here is a link to my old pics that may help you out some.
I tried to get the best bodywork shots possible. Look in the 45 project pics album.
http://community.webshots.com/user/fj45toploader

Note that I made this tub 14" from door post to rear of cab. If I remember right it was 6 or 7" longer than a standard 45 cab.

Just remember that the frame is tappered and you will need to weld in a straight extention piece for it to line back up correcly.
Its pretty easy to do, just measure alot and cut as cleanly as you can on all the parts. Jig saws are great for the body parts.

In the pics, you will see its easier to eliminate the inner rear fender completely and plate where is needed to fill the rear corner floor sections. You will end up with a useless "wedge" that takes up space in the cab if you leave it and is hard to work with.
The floor will match up and can be re-welded to look factory if its cut behind the part where it angles down. For the sides, depending on where you make the cut, you may need to "skin" as the fenderwell will leave a opening. I grabbed a piece of 2'X8' sheet of 16 guage to skin the entire back like a wrap around. And was going to weld it to just under the hardtop lip on the outside and leave a small section of tub to tack on the inside part. I made a paper template to make it easier. Due to rust, and to make it look cleaner, it was easier for me to just end up with a "frame" for the sides to be welded to.

The rear cab mounting can be done by running a custom crossmember along the back of the cab and getting those back mounts to work again with tabs for each hole.
Also look out for the rize in the frame, if you make the cab too long it will hit and need to be cut to clear it. Just more work, or you can lengthen the frame before the front of the rear hanger to avoid this like mentioned above.
The fiberglass hardtop will be easier to line up if you cut it at where the sides bolt to(straight part).
Good luck, its a great project and is fun to work on.
 
nice pics big6lug...thanks for postin em up
(i like those rockwells on that other 40 too...)

malphrus
 
One of my friends is building a short 45 out of a 40 right now. He bought an aqualu tub and used a 40 cowl, on a 40 frame. He made his own body mounts, no big deal there. The problem is (or was) the wheelbase was too short, even with flipping the rear springs. So he extended the frame a foot. Problem solved. It's got a drivetrain from a 60 with a split case and factory 79 p/s. Should be pretty cool. Although recently he did something I didn't think was right, but it worked out pretty slick. He cut a J#$P wrangler tub in half from the doors back. The rear of the tub fits perfect on the back of his rig. I did however insist he runs cruiser tail lights, and remove the J#%P emblems. Should be a cool rig when it's all done.
 
Back
Top Bottom