4" vs 2.75" BS?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 30, 2003
Threads
161
Messages
1,929
Location
Texas, Pinas and Germany
I'm in the process of picking up a set of 38.5/15/16 boggers for my 80 and trying to find out which BS to go with. I decided on a 16 X 10 RockCrawler black steelies 51 series. The 80 has the J lift with L shocks and will be use basically for mudding and occasional DD.Can I use the 80s factory conical lugnuts? Anybody using this setup? :confused:
 
all the 80's ive seen have shank style lugnuts instead of conical/acorn. the rockcrawler rims ive owned and seen need the conical style, and the shank style will not hold properly. hth. with the extra width of the wheel i might think youll need the 2.75 to stay of the frame rails but may get you into fender flare territory.
 
I think the wheels and lug nuts were changed in 95. My '93, my buddies '94, and another buddies '92 all use conical lug nuts and the wheels have a steel seat for the lug nuts.
 
Yup my 91 has conical seats for the lug nuts used them to hold steel soft 8 wheels. No problems.
 
doh i stand corrected. didnt see his 94 in the sig line, however my buddy here just picked up a 94 and it had 5 spoke alloys and shank style lugnuts...... so better check first on your crossover fj>fzj years.
 
I'm in the process of picking up a set of 38.5/15/16 boggers for my 80 and trying to find out which BS to go with. I decided on a 16 X 10 RockCrawler black steelies 51 series. The 80 has the J lift with L shocks and will be use basically for mudding and occasional DD...

Those fat boys aren't going to fit in the wheel wells, so your going to be ether cutting the wheel wells or running huge bump stop extensions. In that case I would get the 2.75 BS to keep them off of the front arms.
 
doh i stand corrected. didnt see his 94 in the sig line, however my buddy here just picked up a 94 and it had 5 spoke alloys and shank style lugnuts...... so better check first on your crossover fj>fzj years.

Thanks. The factory wheels that I have on my '94 uses the conical lugnuts. I'll probably just buy more LC conical lugnuts to use on the new rims that is going on my '96.
 
I tried on some 35" MTRs with 2.5" backspacing on my J lifted 91. It causes all sorts of turning problems going out that far. When you turn the tire comes back into contact with the fender. I think you are going to have a heck of a time with that backspacing and that witdth tire with your size lift even with trimming. You can't really trim into the front doors.
 
My rims are 17X9 with 37s and they fit fine. I do have some rubbing on the fender when they stuff but I don't hit anywhere else. It is very tight though (I have removed all of the mud flaps and have trimmed the front bumper) so I expect that you will have some pretty serious rubbing issues with the extra width and circumference of those tires. The further you push them out the worse it is going to get on the fender so you will have to cut or extend your bumpstops to keep them off. I was originally going to run 1.5" spacers but I suspect if I do that I will have more rubbing issues than I have now.

Kyon
 
Thanks guys. After remeasuring the clearances or lack there of at 5:00 this morning :D, I called 4wheel parts and told them to change it to 4" BS. Lots of work ahead when you go to bigger tires but what the hell. :)
 
Back
Top Bottom