4 Point Seat Belts

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 2, 2003
Threads
7
Messages
28
I am thinking about getting some 4 point seat belts. I have a 71FJ with low back seats with stock belts. I want to get some new seats. If I am using these belts should I be shopping for seats that do not recline or seats that do recline? Do the seats need a slot in the middle for the upper belts to come through? I can fabricate a new seat frame if needed.

thanks
 
I think you will only find seats that do not recline esp. for a harness setup, I can only think the reason would be it colapsing in a accident. :whoops: You can cut holes and put them through....but it may not have the support needed for the forces applied.... :idea: Just a thought.
Good luck
:flipoff2: for the new-B
 
There are a few seats out there with the belt slots that where marketed to the sport import market that do recline. (Civic’s ect.) Personally I would not use them for a harness set up. Of all the aftermarket seats out there the PRP products seem to be the most competitively priced. I have installed a few PRP as well as big $ Beard seats and do not see any difference. http://www.prpseats.com/

If you use a set of seats from a wreaking yard, (some nice ones out there) and you use harness check w/ the belt mfgr. about proper install. You don’t want the shoulder harness too low on the seats, if you are long in the torso. As an example here is a shot of a cage I built for a customer with his Beard seats integrated in the cage. The owner is tall and if the belts went through the slots in the seat they would have been too low. We put a belt cross bar inside the B pillar at the recommended height by the seatbelt manufacturer. This is calculated at the angle off the drivers shoulders to the mounting point. (NOTE: Belt mount points are tabs NOT bolts through the tube. Always use tabs!)

If the shoulder belt is too low and the truck suddenly decelerates the occupants spine is compressed as the body is pushed forward in the harness. If the harness is at the proper height this does not happen and the harness does it’s job.

On the flip side, I prefer healthy set of 3 point OE belts for their freedom of movement on the trail, yet they lock up when needed.

Good luck!

Mark
Belt bar POR.webp
 
helocat said:
Of all the aftermarket seats out there the PRP products seem to be the most competitively priced. I have installed a few PRP as well as big $ Beard seats and do not see any difference. http://www.prpseats.com/
I have PRP front bucket and a rear bench in my 40, I love them!
Good luck :cheers:
 
Here is a shot of the front belt mounting points for the sides.

Mark
Chase side POR.webp
 
GreenWeeny78 said:
Shameless pimping of your products in the pictures mark :rolleyes: :flipoff2:

I thought you were “studying” for finals shop rag. Get back to the books so you can cut some more tube.

BTW: Red Star dude, grow at least a silver star before you go poking the bear, user. :flipoff2:

Mark
 
mxfj40 said:
How do the prp seats compare to the mastercrafts? thanks for all the help


Have note used the Mastercrafts. I hear nothing but good about them as well. $$.

Mark
 
Advent said:
Helocat, when are you going to start including the crossbars on the B pillars and the seat mounts into the full cage? Or at least offer it as an option?

I have wanted to offer a kit for it. It is tough when the OE tank is in place still, to have a full tube mount. The trick is getting the seats to sit low enough and incorporate the side bars. Yes it can and has been done, it’s just best to build the parts to the install. The placement of the A pillars would dictate the width of the seat mounts. Again this can be done but a few more steps. If I get to the point of offering a 100% pre notched kit, I can see offering the seat mounts. This way I could control the alignment and ensure a perfect fit. Until I can shake the machinist out of me I won’t sell a kit if it’s not a perfect fit. (Just would not want it for my truck that way)

Here is a shot of just the seat cradle on this custom build.

Mark
Chase seat mts POR.webp
 
mxfj40 said:
Why the avatar with the middle fingers up? Is that how you greet newbies. If so--thats cool--I feel so welcome here

All newbies get a :flipoff2: but here's another for asking :flipoff2: anyways, welcome
 
Helocat,
What are you running for a fuel cell, and where did you mount it? I have been thinking about incorporating my seats into my cage, but I do not want it to be a PITA when I have to fuel up.
 
Back
Top Bottom