3fe/ 33'/ 4.56?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 13, 2007
Threads
108
Messages
479
Location
Arizona
Ok all my PM is done including the axle rebuild. I can finally start some mods. The list is small and simple. 2.5 lift down from 12.5 to 10.5 ties. Hella lights and some Yakima rack (that can be taken off when not in use.)

The goal is to build a adventure truck that will see a lot of highway miles. Right now the poor 3FE is turning some big tires 33x12.5 that the PO added.

My goal is to be able to hold 75 MPH on the freeway and pull better on hills. How will 4.56 do with 33's? What will it cost parts and labor? I would not be dropping the thirds. Or would I be better off going to a 31 tire for my needs?
 
Not sure about an 80, but my 62 with the 3fe has 33's and pulls 75 just fine on the freeway. Not uphill mind you, but I can easily cruise at 75 on typical hwy stretches with the stock 4.10 gears.
 
I can pull 75, though its a bit of a stretch. Right not the sweet spot is about 65mph, and I have nothing for the hills. I was wondering if going to 4.56 would bump up the sweet spot to 75mph.
 
MJADDICTION (i beleive) really liked his 3FE and 4.88/33'' combo. Might search his name and 4.88 or some combo to find some rpms if you like. Ive only seen two 80's on 33/10.5's but they looked good and both had the 2.5'' lift. Search for Boone and his lift/mods threads..... hes running my old 33 x 10.5's now.
 
I run 4.56 and 33x10.50 on the street. I can do 70 rather easily, but I keep my truck in good tune. Long steep climbs are going to downnshift, but my brother's LX450 on stock tires does the same on the same hill.

SPeedo is very close to GPS with my setup. I'm not sure what you mean when you say, "I would not be dropping the thirds." If you want a gear swap it going to be real hard not to pull the 3rds.

Gear sets will run $250-300 per axle plus OEM replacement parts (new bearings, seals and whatnot) plus labor. Might as well drop in an ARB locker or 2 while you're in the neighborhood.
 
If you are going to change them go to 4.88.


Agree-with 4.88 you'll be close to stock gearing with 33s.

4.56 will be a net undergear-still out of the sweet spot for the transmission-and generating more heat and more frequent downshifts.

You can't change the R&P without dropping the thirds. So do you mean you won't do the work, or do you mean they are not coming out? Changing gearsets is spendy. If you pull and install the thirds figure at least $500 per differential. It will be significantly more if someone else pulls the diffs as part of the work.

Anyway, if you are going to the trouble of regearing, and you want to run 33s, you'll want 4.88s. That way when you decide you want 35s, you'll still have acceptable gearing.
 
4.88s w/ 33s
5.29s w/ 35s +

If only there were 5.71s for the 9.5, cause that would make 37s feel AWESOME!

Yup, agree with this. In my FJ-62 I run 4.56s with Nitto Terra Grappler 265/75R16 that measure 31.5". My speedo is dead on. Driving styles and terrain are going to influence this but personally I would not like less gearing than what I've got with the A440.
 
Based off of numerous reports and first hand experience, I think you'll be happier with 4.88. Its only about 6% lower geared than 4.56, but will be noticeable. Still plenty reasonable for highway speeds.



Ok all my PM is done including the axle rebuild. I can finally start some mods. The list is small and simple. 2.5 lift down from 12.5 to 10.5 ties. Hella lights and some Yakima rack (that can be taken off when not in use.)

The goal is to build a adventure truck that will see a lot of highway miles. Right now the poor 3FE is turning some big tires 33x12.5 that the PO added.

My goal is to be able to hold 75 MPH on the freeway and pull better on hills. How will 4.56 do with 33's? What will it cost parts and labor? I would not be dropping the thirds. Or would I be better off going to a 31 tire for my needs?
 
Thanks guys. What I meant by the thirds is I would not be doing the work, I would have a shop set up the whole thing.
 
Back
Top Bottom