2f TBI performance

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

FLYINGLOW said:
Hey PabloCruise, maybe you can let us all know what you find out from Zaskar by email. I need to learn more about this stuff too. I have been following Mace's thread in hard core about the megasquirt setup. I want to try that setup, it eliminates the distributer from the computer (not 100% sure thats a good thing, but then I can go back to a toy dist.)
I forgot you metion the megasquirt in a prev post...
I have not used it.
I know that the guys in the race circuits do play with them to get more power and tune-ability. I know of a device (don't remember the name) that uses the same ultrasonic tweeter some humidifiers use to vaporize gasoline into the intake instead of relying on heat and air flow for vaporization. If there is something I think that would greatly work in our trucks is that little thing; is that the megasquirt??
 
zaskar_ofn said:
I know that the guys in the race circuits do play with them to get more power and tune-ability. I know of a device (don't remember the name) that uses the same ultrasonic tweeter some humidifiers use to vaporize gasoline into the intake instead of relying on heat and air flow for vaporization. If there is something I think that would greatly work in our trucks is that little thing; is that the megasquirt??

Megasquirt is a computer that you assemble yourself. Its purchased as a kit, circuit board, diodes, resistors blah blah. You assemble it yourself and tune it from a laptop or palm pilot. They can be very basic, as in just running the TBI, or they can be multi port, with timing control.
 
FLYINGLOW said:
checked.
I wouldn't buy it for my TBI setup.
I just read an article on autoweek about this little thing and it is an awesome piggyback. the thing is, I already have all the tuning I want/need by modifying the fuel tables.
Now if you know that the megasquit works for the import computers, like an Acura RSX or in the Tacoma's computer, I'll be all over that thing...
 
I'm running the man-a-fre components with the 'performance distributor' HEI unit in my FJ60 with 235,000 miles on the engine. the TBI eliminated the flat spots the carburator
always had and with the worn out motor and no overdrive i still pull over 15 mpg highway and not much different around town. About 17 mpg on the highway if i cruise 55~60.
Oh, and did i mention, it kicks the carbs ass off road.
 
zaskar_ofn said:
checked.
I wouldn't buy it for my TBI setup.
I just read an article on autoweek about this little thing and it is an awesome piggyback. the thing is, I already have all the tuning I want/need by modifying the fuel tables.

Whats wrong with the megasquirt for the TBI setup?
Whats the little thing (piggyback) that was writen up in autoweek?
 
OK guys I'm back. another weekend...
I'll reply to the last question and then I post what I did this week on the truck.

FLYINGLOW said:
Whats wrong with the megasquirt for the TBI setup?
Whats the little thing (piggyback) that was writen up in autoweek?

there is nothing wrong with the megasquirt for the TBI. I just wouldn't buy it for that because I am already able to configure this the way I want. essentially auto week said the same thing you can read on their web site. no suprise there.

OK, now What I've done with the truck. there is a table called AFR vs MAP that is linked with two other tables and this is how the system gets the Air fuel ratio while not in close loop mode. this table gets read when the engine is fully warmed and the truck enters the hyway mode (i think), open loop idle and some other settings.
I knocked a whole point of this table across all numbers. and the truck actually started running better. (now keep in mind that the old set up was running fine before I had replaced the entire exhaust system for my truck. Now, with headers, hi flow cat and 2.5" exahust piping the engine has become basicaly more efficient.
I didn't think I was going to be able to take one full point off that table but the truck actually seems to run fine and may be there is room for more trimming. Now the question: how do I know when it is enough? well, this is for debate and anybody that wants to say something about it please do so. I think the upper limit is when the engine starts pinging, losses power and/or overheats.
Now I have to go back to the bench. the truck started burning oil and I already know what it is... the oil pump is pumping at high pressure... or the valve seals are trashed...we'll see.
 
Back
Top Bottom