2011 LX570 rear mudflap and connecting pieces install

[Coach Mark]

Hello everyone,
I don’t know when or if I had missed it when I purchased this two weeks ago but I need help identifying a missing piece next to the rear right mudguard. I ordered the mudguard but have been searching two days with no luck on what that other missing piece might be (it’s the red part in the photo). Any help would be appreciated thank you.

 

[sdnative]

If it was the front I would say inner fender liner. Not sure what the rear one is called.

 

[OGBeno]

Try: 77277-60130

Protector for the fuel pipe and wheel well.

 

[Coach Mark]

If it was the front I would say inner fender liner. Not sure what the rear one is called.

Thanks, thought that too then searched for rear fender liner and nothing pops up.

 

[Coach Mark]

Try: 77277-60130

Protector for the fuel pipe and wheel well.

Thank you. I will follow that suggestion.

 

[bloc]

Note that that part number is for a LC.. You'll probably want the one for an LX that has a small access door to get to the AHC fluid reservoir fill port.

LX version is 77277-60140 but you'll also need the little door 77278-60020 and bolt 90105-06321

Also if your mounting hardware for the above panel is missing it's 4x 90166-60003

And lastly.. if you put your year/model in your signature it helps us give correct info.

 

[Coach Mark]

Note that that part number is for a LC.. You'll probably want the one for an LX that has a small access door to get to the AHC fluid reservoir fill port.

LX version is 77277-60140 but you'll also need the little door 77278-60020 and bolt 90105-06321

Also if your mounting hardware for the above panel is missing it's 4x 90166-60003

And lastly.. if you put your year/model in your signature it helps us give correct info.

Thank you! That helps a lot. Also, thanks for the last bit of advice-new to this forum community and always willing to learn and give back.

 

[Coach Mark]

As detailed by Bloc (thank you!), I ordered the parts and was able to install the back panel with the door in it then installed the mud guard after. Not too difficult. I did need a few more of those snap-on bolts (2-3 more would be handy).

Sadly, once done, found out I was missing another panel under the bumper as seen in img 3.

 

[Coach Mark]

@bloc thank you for your help. Got another mystery-any idea what part that’s called under the right rear bumper? The more I look, the more things are missing. Just glad it drives well.

 

[CharlieS]

As detailed by Bloc (thank you!), I ordered the parts and was able to install the back panel with the door in it then installed the mud guard after. Not too difficult. I did need a few more of those snap-on bolts (2-3 more would be handy).

Sadly, once done, found out I was missing another panel under the bumper as seen in img 3.

View attachment 4061030

View attachment 4061031

View attachment 4061032

This version of the panel would also be handy for those of us with Land Cruisers with extended tanks and a fuel pump and vent filter back there! I may need to order these!

 

[bloc]

@bloc thank you for your help. Got another mystery-any idea what part that’s called under the right rear bumper? The more I look, the more things are missing. Just glad it drives well.

View attachment 4061052

I think it's 58723-60010
Some of the attaching hardware might require removing the bumper skin to connect it to the body of the rig..

 

[Coach Mark]

I think it's 58723-60010
Some of the attaching hardware might require removing the bumper skin to connect it to the body of the rig..

Thanks! I will go check it out then report back.

 

[Coach Mark]

Thanks! I will go check it out then report back.

I think it's 58723-60010
Some of the attaching hardware might require removing the bumper skin to connect it to the body of the rig..

@bloc you’re right again. The part finally came in and installed it today. Thanks again for your help.

 

[Coach Mark]

Final install.