1HD-T Snapped crankshaft $$$

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 5, 2016
Threads
2
Messages
30
Location
Aus
Well as the thread title says my 1HD-T has snapped the crank at #2 journal and upon speaking to the Diesel Engine specialist who will be building me a replacement engine it's not the first one that he has come across and very rare obviously.
Damaged caused is extreme: snapped crank, cracked crankshaft cradle and cracked block meaning i have had to source basically second hand replacement items.
Why did it snap? unknown really but i have only owned this car for around 18 months and it's not the engine that it left the factory with, his theory is maybe maybe this engine was removed from a vehicle that was involved in a front end collision? but really never know.
What i do know is i'm looking at a lot of money to build another 1HD-T.
I will use this thread over the next month or so it takes to rebuild a bullet proof balanced etc short motor at the cost of...well to much really!
Pics to follow.
 
20170526_164333.webp
20170609_161102.webp
20170609_161124.webp
20170609_161133.webp
 
Well that sucks. In for pics, not a lot of guys have had to rebuild these, not a lot of tech on the inards.
 
I'd buy a 1hdft or fte instead. I had my 1hdt rebuilt last year after beb failure and the cost was well over $10k USD. You can get a better motor for less money.

Would love to mate but the cost of a second hand 1HDFT here in aus is around 12k! unknown kms, very limited warranty etc not keen on going down that road at all to be honest after this mishap.
Not keen on the FTE due to wiring ecu work etc either.
Also i already have to much invested in the 1HDT: Gturbo, intercooler, new pump & injectors.
My cylinder head is fine though i will get new seals,valves reseated before going back on.
10k USD is almost more than double what its going to cost to have mine rebuilt.
I'm saving lots on labour by doing the head an all other components etc myself

So far this the plan:
New Genuine Toyota late model pistons ceramic coated tops and Teflon skirts.
Second hand block acid dipped,crack tested,machined, decked etc
Crankshaft acid dipped crack tested etc
Short motor fully balanced and assembled
Injector pump will be installed and timed to suit late model pistons and tuned for 27psi
Will also come with a complete genuine gasket kit so all i have to do is drop the head on an reinstall the engine.
That's around $7500 so far including what i paid for the second hand motor (needed a rebuild due to blowby)
 
How much boost were you running?
 
My friend Warren and I have both snapped 3b-custom turbo cranks by running 25 psi boost.
 
My vehicle was only running 21-22 psi so pretty standard for gturbo'd 1HD engine and there's plenty of big hp boosted 1HD engines out there, so i'm leaning towards more of defected crank but will never know why really.
 
Another possible cause is this engine done a head gasket not long after i purchased it and when i removed the head looking for reasons why (didn't get hot at all) i found somewhere along its life the injectors had been replaced (before i had done them) and 5 of the old injector seat washers were left in the head so 5 injectors had double washers under them with only number 4 injector seated correctly on a single washer.
Could this have caused the stress on the crank? again we will never know..

20170201_165238.webp
20170201_165243.webp
20170202_163712.webp
 
If anything the injectors probably would have melted holes in the pistons but I am no expert.
 
The airbox and snorkel - what did you pay for them? I was looking at the moonlight fab products but they're $$$$$$$$$$.

$590 each both company's make awesome stuff but the 2 reasons i went with radius fab was ryco a1358 air filters for this air box can be had for under $20 and second, freight was a lot cheaper to where i live.
 
Could this have caused the stress on the crank? again we will never know

I cant see how. The extra washers would have moved the injectors about 1 mm further away from the piston. I think your crank snapped from either abuse in a previous life or it was faulty. The engine rebuilder may have seen a few because that is his job, but I don't think its all that common.
 
Well I finally split the damaged motor in half and wow! :eek: Here is some pictures for anyone interested.
When I removed the crankshaft the engine block basically started to fall to pieces, also I suspect the root cause is the main bearings
had play allowing the crank to flex you can see bearing shells have started to pit and wear. My engine builder has never seen main bearings
do this on a 1HDT only the conrod bearings which we all know about.

20170901_113216.webp
20170901_113216.webp
20170901_113224.webp
20170901_113204.webp
20170901_120120.webp
20170901_113248.webp
 
Main bearing shells
20170901_115807.webp
20170901_115812.webp
20170901_115817.webp
20170901_115836.webp
 
On a brighter note my replacement engine was finally completed today and looks pretty good I think :smokin: some people may not like the colors I chose but I think it will look good in my white engine bay with the chrome top mount intercooler and stainless snorkel and air box.
This a fully balanced 1HDT with all genuine parts including the later model pistons ceramic and teflon coated :D
The tax man was really nice to me this year so i decided to get the whole engine assembled and painted by my engine builder.
Anyway here it is my caterpillar 1HDT :cheers:
FullSizeR.webp
Pistons.webp
P.webp
IMG_0459.webp
 
Last edited:
Completed ready for transport :clap:
48.webp
49.webp
50.webp
51.webp
52.webp
 
Back
Top Bottom